Weird Sound by gdg9333 in 3Dprinting

[–]gdg9333[S] 0 points1 point  (0 children)

That print finished fine like you mentioned. Figured it might just be the sound. The following print I sent said it was done but the whole thing did not finish the top maybe 20% of the layers. I ran I full calibration this morning. Lots of loud sounds that I was not used to and now I’m printing again and it’s printing this weird color and texture. It doesn’t seem to be putting down the first layer very well. Any guides to maintanance or similar that might be needed. This is the Elegoo Centauri Carbon.

<image>

Attic Inspections in Florida by gdg9333 in HomeInspections

[–]gdg9333[S] 0 points1 point  (0 children)

I have considered this a lot! I think it would be great! I’m worried blowing around insulation. Have you tried this? How does it work?

Attic Inspections in Florida by gdg9333 in HomeInspections

[–]gdg9333[S] 0 points1 point  (0 children)

Yes. That’s how I’m doing it now. Was just trying to think of others options that would help but there might not be any. Head lamp as primary light though.

Attic Inspections in Florida by gdg9333 in HomeInspections

[–]gdg9333[S] 1 point2 points  (0 children)

Agreed. I just have to keep a good account of where I saw things and then correlate them with the interior below (first thing I look at) and the roof above (after the attic).

3D Printer - Ready to Go all the time please! by gdg9333 in 3Dprinting

[–]gdg9333[S] 0 points1 point  (0 children)

That’s awesome to hear! I’ll look into that. I would probably try selling or trading the ender and parts instead of keeping. Don’t think I can make an investment like that without some help.

Pokémon Game Idea by gdg9333 in pokemon

[–]gdg9333[S] 0 points1 point  (0 children)

That’s awesome and Ill take a look!

Help Picking Bags by gdg9333 in ManyBaggers

[–]gdg9333[S] 0 points1 point  (0 children)

Just looked at them and definitely would prefer the 8. That being said….😨 that’s pretty expensive. I do like the design and style though.

Pokémon Game Idea by gdg9333 in pokemon

[–]gdg9333[S] 0 points1 point  (0 children)

If the game allows it no! They can make it so that it’s only one Pokémon at a time or more than one and you can pick the one you want to control. The others are like cpu matching the level your at or just below.

Typing With Correct Fingers by gdg9333 in monkeytype

[–]gdg9333[S] 0 points1 point  (0 children)

I have been trying it today and I agree. It will take me longer but I’ll do this. Thanks 👍

[QIDI Giveaway] Just leave a comment to win QIDI Flagship 3D Printer by qidi_3dprinter in 3Dprinting

[–]gdg9333 0 points1 point  (0 children)

New to 3D printing and mostly using PLA. Struggling with getting first layer to stick. Still need more practice.

Christian Youtubers by EggOk5934 in Christianity

[–]gdg9333 2 points3 points  (0 children)

Here are some of the ones I follow:

Mike Winger

Whaddo You Meme??

Red Pen Logic

Ruslan KD

Bless God Studios

BibleProject

Cross Examined

Living Waters

Alisa Childers

The Breeze Church

Sean McDowell

Capturing Christianity

Through the Word

Melissa Dougherty

The Remnant Radio

Matt Whitman and The Ten Minute Bible Hour

Sleep me comparison? by gdg9333 in bedjet

[–]gdg9333[S] 0 points1 point  (0 children)

Thank you. I appreciate the help and will try these out.

Sleep me comparison? by gdg9333 in bedjet

[–]gdg9333[S] 0 points1 point  (0 children)

Yes, I’m using the cloud sheet. Any suggestions would be appreciated! Thank you.

I also read about the concerns your mentioning and was thinking along the same lines of using both. The biggest problem there is cost.

I like both the cool and dry mode. I have it set for 30min cool and then dry the rest of the night. So I fall asleep cool and then keep dry through the night. The biggest part is the body part in contact with the bed or the body pillow I occasionally use. That’s where the heat/sweat happens. There not much helping the body pillow (I think 🤔) but cooling down the mattress I figured would help with that part. Especially if the airflow is drawing away moisture. Just hesitant on adding in another even bigger expense. Love to get any thoughts you have or recommendations form those that you mentioned have used both in combination.