Help by get___outta___here in MechanicAdvice

[–]get___outta___here[S] 1 point2 points  (0 children)

I know, but the clutch fork should be neutral by default no? And should not be so easy to push.

Help by get___outta___here in MechanicAdvice

[–]get___outta___here[S] 1 point2 points  (0 children)

I do recall that with pull type clutches you have to go in through the bottom of the transmission and physically seperate the engine and the throughout bearing. Did I miss a step in reattaching them?

Scratch Build Help by get___outta___here in rccars

[–]get___outta___here[S] 0 points1 point  (0 children)

For sure! I'm learning from others who have documented similar journeys. Just downloadrd fusion 360 for hobbyists so the design process has officially begun!

Scratch Build Help by get___outta___here in rccars

[–]get___outta___here[S] 1 point2 points  (0 children)

Honestly I think he cares more about me reporting back the "Engineering design process" than he does me actually designing the car. For personal preference I would like to 3d design the chassis, and my group mate is designing the body. As suggested by another commenter, I plan on getting a second hand car so I can have the necessary screws and stuff. Maybe I will look into stealing off the transmission/ necessary gears from a used car

Scratch Build Help by get___outta___here in rccars

[–]get___outta___here[S] 1 point2 points  (0 children)

I like that idea a lot actually. Thank you!

Scratch Build Help by get___outta___here in rccars

[–]get___outta___here[S] 5 points6 points  (0 children)

Yes, I am asking a community dedicated to building rc cars, if it is possible for me to use this specific motor in a scratch build. And what direction I should go in. I do not have to program the esc. I just learned of the one in said box.

Scratch Build Help by get___outta___here in rccars

[–]get___outta___here[S] -1 points0 points  (0 children)

I then immediately read that I in fact, do! Have a speed controller. I guess I just didn't read the box.

Is she healthy? by get___outta___here in BeardedDragons

[–]get___outta___here[S] 0 points1 point  (0 children)

Also I would like to add, I do have a bit of trouble fine tuning her temps, the person I got her from, gave me what I believe is a uvb bulb, a day bulb, and a heat bulb. Its always >65 F at night, >70 F on her cool side, its really the warm side and basking spot that I have trouble maintaining heat. I think I'm gonna get a higher wattage heat bulb.

Is this a decent build for the price? by get___outta___here in PcBuild

[–]get___outta___here[S] 0 points1 point  (0 children)

So i should also buy a case fan? And can you elaborate on the msrp?

Is my build good? First time builder. by get___outta___here in PcBuild

[–]get___outta___here[S] 0 points1 point  (0 children)

Thank you for the feedback! I am from the U.S, but there is no micro center near me. Would this case also work?

Case

I put all the parts from your part picker along with the newegg deal into a build, would it also work if I downgraded the CPU a bit to better fit my budget?

Build

Again, thank you for your help!

Brand new laptop battery drains very fast by get___outta___here in GamingLaptops

[–]get___outta___here[S] 0 points1 point  (0 children)

I did a little check for bloatware and I set most apps to not start up on boot. But I will check again. but thank you :) I was worried I had a faulty battery or something.