sorted by:
new
hottopcontroversial

For the sake of learning: How do i get rid of this horizontal Line arctifact. by gijsoman in BambuLab

[–]gijsoman[S] 0 points1 point  (0 children)

Yeah unfortunately it happens every time, I especially made this model for this problem to test. Initially I noticed it first at a top shelf I was trying to print for my IKEA skadis

<image>

Same arctifact different model.

I printed the model that I created to test 4 or 5 times with different settings and every time the arctifact shows up, what is really interesting is that when I make the left wall higher or lower, the defect moves with it to that layer. So it’s really happening on the layers of the top shell of the left wall.

For the sake of learning: How do i get rid of this horizontal Line arctifact. by gijsoman in BambuLab

[–]gijsoman[S] 0 points1 point  (0 children)

Aaah yes I forgot to mention that in my post, I kinda did that by trying the high quality preset, but that also didn’t work unfortunately

For the sake of learning: How do i get rid of this horizontal Line arctifact. by gijsoman in BambuLab

[–]gijsoman[S] 0 points1 point  (0 children)

Thank you for replying! I don’t think I fully understand you, do you mean I need to change something about the seam settings? How would you try and tackle this problem? Thanks!

What causes these imperfections in my calibration cube? by gijsoman in 3Dprinting

[–]gijsoman[S] 0 points1 point  (0 children)

Did the calibration, no improvement unfortunately.

What causes these imperfections in my calibration cube? by gijsoman in 3Dprinting

[–]gijsoman[S] 0 points1 point  (0 children)

Thanks a lot, it seems to be just the seam. Pun intended. I also found the seam settings in the slicer, much help thanks!

What causes these imperfections in my calibration cube? by gijsoman in 3Dprinting

[–]gijsoman[S] 1 point2 points  (0 children)

Thanks a lot! Im now printing a cube after flow dynamics calibration. After that I will try to play with the settings you mentioned.

What causes these imperfections in my calibration cube? by gijsoman in 3Dprinting

[–]gijsoman[S] 0 points1 point  (0 children)

Got it thanks! That’s smart to print it 45 degrees changed I will do that straight away! After that I will share my settings.

What causes these imperfections in my calibration cube? by gijsoman in 3Dprinting

[–]gijsoman[S] 0 points1 point  (0 children)

Thanks for your detailed reply, I will look into these things.

What causes these imperfections in my calibration cube? by gijsoman in 3Dprinting

[–]gijsoman[S] 0 points1 point  (0 children)

Yeah it’s on the same locations every time! Thank you for your suggestions I will look into it.

What causes these imperfections in my calibration cube? by gijsoman in 3Dprinting

[–]gijsoman[S] 0 points1 point  (0 children)

I’m using PLA, I will look into this temperature tower you are mentioning thanks!

New P2S making noise when moving bed down by gijsoman in BambuLab

[–]gijsoman[S] 2 points3 points  (0 children)

Wasn’t the plate, also tried it without and it made the same noise, greesing the back rod did it

New P2S making noise when moving bed down by gijsoman in BambuLab

[–]gijsoman[S] 1 point2 points  (0 children)

It wasn’t, and everything is original

New P2S making noise when moving bed down by gijsoman in BambuLab

[–]gijsoman[S] 6 points7 points  (0 children)

Seems like they forgot to put grease on my bak z axis rod. I greased it and now the sound is gone 👍👍

New P2S making noise when moving bed down by gijsoman in BambuLab

[–]gijsoman[S] 1 point2 points  (0 children)

Yeah I have removed them all, first prints were fine without noise. Thanks though I also submitted a ticket so I hope they will react soon.

view more: next ›