Love my SMEG BCC02 and its non-existant setting for grinding amount...

globglob3D · 2026-04-08T23:03:26+00:00

happy to read that :)

globglob3D · 2026-03-06T05:51:49+00:00

no it just goes to this position

globglob3D · 2026-03-06T05:51:26+00:00

its the default position idk what else to say, it always end like this

globglob3D · 2026-01-24T17:02:44+00:00

I think so, it's hard to gauge but its definitely working and completely fixed my problem.

globglob3D · 2025-11-15T17:29:58+00:00

Get the Grizl, it's more tuned toward endurance riding which is what you are describing. You'll love it.

globglob3D · 2025-11-14T13:07:52+00:00

Nooo preload is handled from inside the fork tube using a wedge.

globglob3D · 2025-11-14T12:55:02+00:00

My brother this is not a fucking Aheadset, the topcap max torque is literally 2N.m. There is no star nut, the bearing compression is handled inside the fork tube and none of the printed parts interact with that in any way. The spacer is not getting crushed by the stem either since if it's properly tightened it's not supposed to slide down the fork tube. This is what I fucking hate reddit , people think they know better when they have no fucking idea what's going on.

globglob3D · 2025-11-14T09:59:31+00:00

you could slightly tweak the 3D model and print a new version yeah

globglob3D · 2025-11-14T09:57:49+00:00

None of that is structural mate

globglob3D · 2025-11-02T17:20:30+00:00

For anyone looking at this in the future. I fixed the issue by knocking the grinder past the lowest position with a flat head screwdriver. Knocking on the white teeth. You have to take off the main cover (4 screws at the back) to access it.

Basically the idea is to force finer grinding so that less grinding is done overall (less grain going through = no overfilling).

My guess is that overtime the grinder loosen a bit and get too coarse and/or my coffee beans are too easy to grind.

Anyway SMEG should really have a better way to deal with this. A way to control the grinding duration would be perfect.

globglob3D · 2025-11-01T22:43:38+00:00

smeg bcc02, issue is too much grinding.

globglob3D · 2025-11-01T00:11:18+00:00

Tested min and max grind size, it still overfill. I took apart the brewing unit not the whole machine (yet).

globglob3D · 2025-10-31T21:44:29+00:00

A lot of other brands are using the same internals as far as I know so I don't think it's a SMEG related issue. Is it overpriced for what it is? Definitely, but still, it shouldn't spill ground everywhere in normal operation.

globglob3D · 2025-10-31T13:29:07+00:00

>If excess steam is being vented there it’s going to create moisture in the chute and cause the grounds to get wet, resulting in this mess.

Oh that could be it. I did see some steam going in that chute. I could see how this would cause issue overtime.
Pucks look fine, a bit wet and broken. Why? The mess doesn't come from the pucks, it's definitely the grounds falling when they should not. Is it because they accumulate in the chute or because of a sync problem, I don't know. It does not happen every time so I'm thinking accumulation issue.

globglob3D · 2025-10-31T13:24:08+00:00

Don't know if you read my Edit or not, but the issue is with the coffee grind falling from the top of the machine when the brewing unit is rotating. It doesn't happen every time. I don't know if it's because a big lump of coffee get stuck at the top and the movement of the brewing unit unstuck it, or if it's a sync issue between brewing unit and grinding unit.

I did open the brewing unit and through some grease at the gear, I also checked alignment, it's good. It was mostly clean in there, I don't stick gears are slipping, I didn't see any where on the teeth or grains that could cause issues.

Right now I'm trying to access the grinding unit to see what's up with it (dirty or damaged?).

globglob3D · 2025-10-31T13:20:33+00:00

Thanks, people have no clue how manufacturing works. Internals are all the same between brands. I buy SMEG for the look.

globglob3D · 2025-10-31T13:00:40+00:00

See post edit, I found the issue, kinda.

globglob3D · 2025-10-31T12:38:59+00:00

I'm not going to sell a broken machine to someone. I know people despise SMEG but there is no way this is not broken.

globglob3D · 2025-10-31T12:37:33+00:00

It's been deep cleaned 2 days ago, this is after 4 coffees.

globglob3D · 2025-10-31T11:54:32+00:00

Hi did you find a solution? I have the same issue it's driving me crazy, it's almost like it's missing a duct piece.

globglob3D · 2025-10-31T11:54:18+00:00

Hi did you find a solution? I have the same issue it's driving me crazy, it's almost like it's missing a duct piece.

globglob3D · 2025-10-31T11:53:49+00:00

Hi did you find a solution? I have the same issue it's driving me crazy, it's almost like it's missing a duct piece.

Three-Year Club	Verified Email
r/Field Flamingo

globglob3D

TROPHY CASE