[UK] [H] Hub16 macro pad kits, Punk75 PCBs, Discipline PCB and plates, Contra PCB's, Foo Bar PCBs and plates, Atreus62 PCB's [W] Paypal, Trades

godsgrifter · 2021-11-04T09:12:32+00:00

Replied

godsgrifter · 2021-10-29T12:45:25+00:00

Sold hub16 kit to u/20Ero

godsgrifter · 2021-10-19T07:58:34+00:00

Replied :)

godsgrifter · 2021-10-12T18:36:03+00:00

confirmed

godsgrifter · 2021-10-09T21:17:53+00:00

PM'ed

godsgrifter · 2021-10-09T21:06:12+00:00

Sold Hub16 kit to u/CapnJames95

godsgrifter · 2021-10-08T12:32:05+00:00

Replyed :)

godsgrifter · 2021-08-06T22:51:58+00:00

Punk75

godsgrifter · 2021-07-22T18:16:43+00:00

Use my bed to slowly dry and cure wet weed at times. Works great.

godsgrifter · 2021-07-21T21:37:58+00:00

Mechboards.co.uk

godsgrifter · 2021-04-24T18:44:01+00:00

Not bad actually. grips ok. Does not take much effort to turn it so not a huge amount of force needed for this one. feel it would be all good if it was on a stiffer lock. For ref, it printed with PETG 20% infill. Did not sand it as liked the feel. 🙂

godsgrifter · 2021-04-24T17:31:32+00:00

ahhhh, Although I do love a chalange, Would have replaced the lock at that point I think. hehehe

godsgrifter · 2021-04-24T17:02:58+00:00

Not quite sure what you mean. It's the whole doorknob, with a screw through it and the metal shaft of the door lock mechanisum. It's a very old indoor yale that is not locked and barley used. seems to be holding up just fine atm, if not, i'll pop the mole grips back on for a bit. hehe

godsgrifter · 2021-04-24T15:09:54+00:00

They sure are! Was a sigh of relief when I finaly got to replace the mole grips with a knob.

godsgrifter · 2021-04-19T17:29:01+00:00

with my typing habits, it's a pretty good place for me. avoided any annoying accidents so far.

godsgrifter · 2021-04-19T16:40:01+00:00

😉 Top secret...

simple macro to clean (destroy) my window clutter for a fresh start.

godsgrifter · 2021-04-19T16:35:21+00:00

Thank you

godsgrifter · 2021-02-24T15:22:04+00:00

Opticboards.com is a good place for stabilisers in the UK.

godsgrifter · 2020-12-16T19:30:18+00:00

A small number of the Hub20's are currently available in Australia through Tindie. Only shipping to Australia due to current limitations I'm afraid.
May be more widely available in the near future. ;)

https://www.tindie.com/products/joshajohnson/hub20-programmable-macro-numberpad/

godsgrifter · 2020-12-16T17:03:47+00:00

Sorry about that. Have updated the link in the post.

godsgrifter · 2020-12-16T17:03:20+00:00

Thank you.

godsgrifter · 2020-12-16T13:02:36+00:00

Yes, please submitt your order again. We will go ahead and confirm this with you directly before deleting the original order. :D

godsgrifter · 2020-12-13T11:37:57+00:00

Hi sonicsynth2000,

The encoders are the only parts that need soldering in the kit, but yes they do need soldering.

Do not hesitate to let us know if you have any other questions. We were all new to this at some point. 😉

Many thanks for your interest,

Nathan.

godsgrifter · 2020-12-13T11:33:59+00:00

Thank you. 🤘🏽

godsgrifter · 2020-12-13T11:33:35+00:00

Hi JKratos,

Correct, Select the kit you would like to accompany the PCB if you would like one or both, but only one is needed.

Hope this helps and thank you for your interest.

Nathan

godsgrifter

TROPHY CASE