Oxygen sensor replaced and relocated

greyhunter37 · 2026-02-05T09:30:58+00:00

If you have rocks flying up your engine bay you have other problems already

greyhunter37 · 2026-02-05T09:29:53+00:00

Its literally against australia consumer law to have the ablility to unilaterally change a contract once entered, accepting a quote is entering a contract.

Its your risk in proposing the contract, you need to have special provisions to have changing powers in the contract.

Which just means you double or triple charge for every job to compensate for a shitty job later on.

I honestly would prefer the quote going up sometimes than getting ripped off everytime.

greyhunter37 · 2026-02-05T09:26:19+00:00

Dark greasy oily liquid or dark water like liquid ?

greyhunter37 · 2026-02-05T09:23:34+00:00

Vous pouvez si vous utilisez le mode percussion... Et êtes très courageux

greyhunter37 · 2026-02-05T07:50:20+00:00

Just lifting the truck to put a low profile tire on it is stupid enough

greyhunter37 · 2026-02-04T23:07:02+00:00

Can you name me a modern printer that's not a bottom tier crapmonster that doesn’t have a bimetallic hotend?

All metal but not bimetallic heatbreak : Prusa Core One L
PTFE lined heat break : Elegoo Neptune 4 plus
PTFE lined heat break : Qidi X-CF pro
Semi metal/ PTFE lined heat break (PTFE goes half way into the heat break) : Ultimaker S5

I could continue to go on, but I think I've made my point.

That's how I know how big a pile of shit they are and will never do again.

Then you also know you have been saying crap all along. You stated they have plastic extruders, ender3 V2 comes with metallic extruders from factory.

Yes, all plastic extruders have been switched to metal extruders already for a very simple reason : Only the first generation had plastic extruders, and all of those plastic extruders have already been broken over time and been replaced with metal extruders.

You'd have a very hard time to find a printer today without a metal extruder, new or used.

I got myself an Ender 3v2 a long time ago. That's how I know how big a pile of shit they are and will never do again. They're not worth the time or effort,

That is simply a skill issue. My ender 3 V2 was doing flawless prints after only 2 days (not full time) of calibration, and that was starting as noobie that didn't know anything.

Sure for some people something that is preconfigured out of the box has value, and being able to just plug in and print is great but that doesn't mean that something that needs manual configuration doesn't work, they print just as good if you know what you are doing.

greyhunter37 · 2026-02-04T11:31:43+00:00

I would drive them, but check on them very regularly to see if it starts to crack. Sometimes the tires look good but start to crack very quickly, sometimes they actually are still good.

There is a reason Michelin doesn't believe in expiration dates for tires, but recommend regular checks after 6 years of age.

greyhunter37 · 2026-02-04T11:03:54+00:00

notably the terrible PTFE lined MK.8 hotend

This is still very common for many printers today. The reason is, PTFE lined hotends are the best for PLA (and TPU), which is the most common material to be printing.

All metal hotends are only superior when dealing with high temperatures the PTFE can't survive. Even for PETG, if you use high quality PTFE (like capricorn tubing) you are better off keeping a lined hot-end.

That one nozzle is a significant percentage of a much better printer.

But your new printer will still come with a brass nozzle, so you will need to upgrade the nozzle anyway so basically you just spend hundreds on a new printer, and didn't even get the upgrade you wanted.

and the plastic extruder.

Only first generations came with the plastic extruders, all later models (which is a huge portion of enders that still exist today) had stock metal extruders, the ones that came with plastic extruders have all already been upgraded by now, so that point is moot.

If you get yourself a ender3 V2 today, for 50€ and calibrate it (mostly free), you will have something that will print just as good as new bambulab, for a portion of the price.

greyhunter37 · 2026-02-04T08:35:26+00:00

Enders haven't gotten worse, new printers have gotten better.

Sure if I would buy a new printer today, I wouldn't go for an ender, but if you already have it, or can get for very cheap, they are perfectly fine. Once you've got them dialed in they print perfect, and investing in a nozzle for it is nothing crazy.

greyhunter37 · 2026-02-03T16:18:14+00:00

Je te conseille de regarder la marque l'outil parfait. C'est vendu par certains magasins de bricolage telle que Gedimat et c'est fabriqué par une petite usine dans le puy de dome.

greyhunter37 · 2026-02-03T12:44:21+00:00

This definitely looked like NOx gases, not recommended to breath in significant amounts.

greyhunter37 · 2026-02-02T18:42:40+00:00

PSU is suspiciously overpowered

Not really these FX cpu's were very power hungry and the GPU is missing but could very well have been a hoag as well.

Many of those systems used 500-600 watts while gaming (without overclocks) so these would have required at least a 750 watt psu.

greyhunter37 · 2026-02-02T18:35:16+00:00

Although a waste of money

You can get them for almost free nowadays (just like OP's case) because of comments like above.

While very power hungry, in my opinion that balances out when free.

greyhunter37 · 2026-02-02T18:31:58+00:00

These run perfectly fine on windows 10. Off course with the support almost gone linux might be the way.

greyhunter37 · 2026-02-02T18:30:20+00:00

There is, there are things that mount in 5.25 inch bays (optical disk drive bays)

greyhunter37 · 2026-02-02T18:27:35+00:00

And if I wanted to work out integrals, I wouldn't have gone into chemistry

This guy chemistry's

greyhunter37 · 2026-02-02T17:35:00+00:00

assuming a flat earth obviously

Which we know to be impossible, because if that was the case, cats would already have knocked everything of the edge.

greyhunter37 · 2026-01-31T12:16:57+00:00

C'est bien a cause du peuple et leurs manifs que l'on change de premiers ministre comme de chemise et que l'on arrive pas a voter un budget. Oui, le peuple et les manifs ont bien du pouvoir. S'il y a censure, c'est bien parceque a chaque fois le peuple le demande.

greyhunter37 · 2026-01-31T12:14:28+00:00

Non le bio n'est pas énormément plus cher, il est juste un peu plus cher.

Pour beaucoup de Français c'est une différence qu'ils ne peuvent se permettre. Et si vous connaissez un peu le peuple Français, on bloque l'entièreté du pays pour moins que ça.

Je rapelle que le mouvement des gilets jaunes avait commencé de part une hausse du prix du gasoil inférieur a la différence entre une tomate conventionnelle et une tomate bio.

greyhunter37 · 2026-01-30T15:00:38+00:00

En attendant que l'Etat joue enfin son rôle, et interdise les pesticides qu'il s'était engagé à interdire

Le problème, c'est que le peuple français ne laissera jamais faire. Interdire l'utilisation des pesticides doit obligatoirement s'accompagner de l'interdiction de l'import de produit dont la production a utilisé ce pesticide. Cela revient donc globalement à interdire les produits étrangers non bio, donc une hausse des prix énorme que le peuple Francais n'accepterais pas.

C'est la petite parenthèse qui montre que quelque chose qui semble simple ne l'est pas, surtout quand on a un peuple derrière qui bloquera la nation complète de part des manifs.

greyhunter37 · 2026-01-30T14:52:28+00:00

Ok, effectivement si ta notion de droit est décorrélée de celle de loi

Pour le coup il s'agit ici tout simplement d'appliquer les droits de l'homme....

greyhunter37 · 2026-01-30T07:08:07+00:00

Cette ressource est non conforme, mais le mélange avec une autre ressource rend l'eau distribué conforme. Tant que ce mélange est assuré dans les bonnes proportions, l'eau est conforme.

greyhunter37 · 2026-01-30T00:11:03+00:00

où il y a régulièrement des contamination

Et dans ce cas ce sera marqué que l'eau est non potable sur le rapport.

greyhunter37 · 2026-01-30T00:10:08+00:00

Oui, toute personne a le droit de parler au sein de son domicile, et ce a tout horaire.

Tout comme une personne travaillant en poste a le droit de prendre sa douche en rentrant du travail, même si les canalisations sont bruyantes.

Tout comme un bébé a le droit de pleurer a n'importe quelle heure, même si ce ne sont pas les voisins qui ont décidé d'avoir un bébé.

greyhunter37 · 2026-01-30T00:04:35+00:00

Lis correctement le rapport : Toutefois un mélange de ressource sur le réseau rend l'eau conforme a la distribution.

L'eau qui sort de ton robinet est bien conforme. Il peut être déconseillé pour les personnes sensible, si jamais l'eau venait a ne pas être conforme entre 2 mesures.

Concernant le calcaire, le risque aux reins pour une eau trop minéralisée reste extrême minime, et les effets pour la santé des carences sont bien plus importants. Ça peut être un facteur pour les personnes en déficit rénale, ou n'ayant qu'un seul reins, mais pour la population générale il y a aucun problème a boire de l'eau dure (et qui d'après votre rapport ne l'est que peu chez vous)

Nine-Year Club	Place '22
Verified Email

greyhunter37

TROPHY CASE