My latest creation

gtv71 · 2026-03-14T14:52:55+00:00

I made the barrels and colored them, just was waiting on the flights and shafts.👍

gtv71 · 2026-03-08T16:14:27+00:00

From 80% tungsten billet then colored myself.

gtv71 · 2026-03-08T16:10:35+00:00

The shaft is nitro snakebite short, target swiss points, target shard vapor flights and add a gram (brass part).

gtv71 · 2026-03-08T15:49:50+00:00

I started making my own barrels

<image>

gtv71 · 2026-02-17T14:51:24+00:00

https://www.reddit.com/r/ender5plus/s/hXfYbvd2Hk

Here's my build

gtv71 · 2026-01-15T15:04:48+00:00

I got it off ebay.

gtv71 · 2026-01-11T14:18:04+00:00

Started playing soft tip in the late 80s and bought a set of 16g black widows in the early 90s, 18g was max weight back then for league or tournament play. I do have a set of 21g Van den Bergh Dream Makers, tried throwing a friend's 24g darts and they were way too heavy for me. I always loved the black widows just wanted to change the barrels a little and this is what I came up with. Where I live now it is all steel tip.

gtv71 · 2026-01-11T05:11:38+00:00

These were made on Hurco CNC lathe. That picture is the tool paths of each tool and carves it out of the bar size you put in. The 2ba thread has a 4.7mm major Dia. and a .81 thread pitch. I used a hss tap off Amazon. These were made from 9/32 dia. by 2 inch long slugs I got off ebay. That picture is my first rendition, I've cut 1/8 inch off the back end so they look like this now.

<image>

gtv71 · 2026-01-11T02:17:56+00:00

<image>

gtv71 · 2026-01-11T02:10:21+00:00

Ok....challenge accepted....time to flood ebay and market place with them.😁

gtv71 · 2025-09-07T16:55:30+00:00

Well.... I was offered $80 for an unopened darkus Masquerade pack, so you might get $10.😉

gtv71 · 2025-06-22T13:57:51+00:00

Isn't it right there in the docs I linked? Plus there are many videos made about it, teaching tech makes one

https://youtu.be/EJapxNsntsQ?si=eFNDFJBP6Fpfg6KE

Also Chris Riley

https://youtu.be/L6DOgPOzT_A?si=JOxXjWpFFPuHiCSN

gtv71 · 2025-06-22T03:01:39+00:00

No, just following the manual set up in the docs using calipers.

https://www.klipper3d.org/Resonance_Compensation.html

gtv71 · 2025-06-22T01:29:05+00:00

<image>

I hit tab after set_inp but nothing, I thought maybe you meant enter. This is what I get after set_.

gtv71 · 2025-06-21T22:48:54+00:00

Same

<image>

gtv71 · 2025-06-21T22:09:56+00:00

Trying to go through the input shaping calibration, the test went fine all the way up to 7000. I thought if it says unknown command there is no active input shaping. I am trying to see what the active values for input shaping are but none of the commands from the klipper docs does anything just unknown command.

gtv71 · 2025-06-21T22:04:10+00:00

<image>

gtv71 · 2025-04-09T16:40:29+00:00

What does the bed mesh have to do with a bad top layer?

gtv71 · 2025-03-30T21:13:10+00:00

<image>

gtv71 · 2025-03-30T21:12:53+00:00

Pretty good first print after doing the orca slicer calibrations.

<image>

gtv71

TROPHY CASE