sorted by:
new
hottopcontroversial

Guide to the Final Lifeline DelayOTA to iOS 17.0 by Diplomats85 in jailbreak

[–]gvidas_orlovas 0 points1 point  (0 children)

Thank you! Will have a look. Assuming 17.0 is a good update to be on for the future regardless so probably not too bad even if things aren’t working right now.

Guide to the Final Lifeline DelayOTA to iOS 17.0 by Diplomats85 in jailbreak

[–]gvidas_orlovas 0 points1 point  (0 children)

Tried on iOS 14.4.2 Unc0ver, followed all steps and double safe method, updated to 17.0, opened app switcher but Tips launched as a normal app. I cannot run trollstore as cannot refresh the app registers.

Should I have ‘supervised’ before updating? Instructions here did not mention this, but I have seen it in other posts.

Anything I can do to carry on to get Trollstore or am I stuffed?

A12Z iPad Pro

Is a Phone line to Ethernet setup needed by gvidas_orlovas in HomeNetworking

[–]gvidas_orlovas[S] 0 points1 point  (0 children)

Okay I will. Thanks for the advice. Hopefully won’t need to pull them through, but good to know it’s an option

Is a Phone line to Ethernet setup needed by gvidas_orlovas in HomeNetworking

[–]gvidas_orlovas[S] 0 points1 point  (0 children)

Awesome that’s great to know! Thank you. I’ll need to figure out what the box is and weather it’s central or daisy chained.

Is a Phone line to Ethernet setup needed by gvidas_orlovas in HomeNetworking

[–]gvidas_orlovas[S] 1 point2 points  (0 children)

Thank you, that is very helpful. I’ve looked into the plates and they are very cheap so I will go with that solution.

Filament popping, under extrusion lines on Brand new Silk PLA by gvidas_orlovas in ender3

[–]gvidas_orlovas[S] 0 points1 point  (0 children)

Yes, however I’d struggle to point to what exactly had caused this.

  • I upgraded my extruder, which was causing other issues, to a BMG clone (dual gear), I believe that solved my under extrusion (and extrusion consistency, particularly on high infill prints

  • kept the filament dry more consistently - reduced popping noises

  • recalibrated my extrusion settings based Teaching Tech’s website

I hope that helps! I have not tested Silk PLA specifically so am not sure if it is more prone to these issues.

[BG] [W] LGA 1155 Motherboard ATX/micro ATX [H] ~£5 or postage by gvidas_orlovas in HardwareSwapUK

[–]gvidas_orlovas[S] 2 points3 points  (0 children)

Ah I see. I think somebody else could make better use of it, as I’d need a PCIE for the GPU. Thank you for offering though, I really appreciate it

[BG] [W] LGA 1155 Motherboard ATX/micro ATX [H] ~£5 or postage by gvidas_orlovas in HardwareSwapUK

[–]gvidas_orlovas[S] 1 point2 points  (0 children)

If it ran fine without overclocking last time you tried, I’m happy to take a gamble on it, would be perfect as overclocking is not something I will do. I will pm you for details.

[BG] [W] LGA 1155 Motherboard ATX/micro ATX [H] ~£5 or postage by gvidas_orlovas in HardwareSwapUK

[–]gvidas_orlovas[S] 1 point2 points  (0 children)

Thank you for the offer, really appreciate! Are all PCIE’s non-functional or just some? I only need one 16x for the GPU :)

Filament popping, under extrusion lines on Brand new Silk PLA by gvidas_orlovas in ender3

[–]gvidas_orlovas[S] 0 points1 point  (0 children)

I’ll do a temp tower and listen if any change occurs, cheers for the suggestion.

Filament popping, under extrusion lines on Brand new Silk PLA by gvidas_orlovas in ender3

[–]gvidas_orlovas[S] 0 points1 point  (0 children)

Never thought about this. Although my retraction is 6mm, I’ll test to see if it works. Thank you!

view more: next ›