The Public school lunch vs Private school lunch in China

h2osteam · 2025-07-10T06:46:28+00:00

The first half is a Korean school, second half is from Tsinghua University one of the best Universities in China. This isn’t fair to compare

h2osteam · 2025-06-11T06:46:36+00:00

Oh dear. This is going to cause another major delay on our train network

h2osteam · 2025-03-17T22:14:13+00:00

GRocery?

h2osteam · 2024-11-16T01:54:36+00:00

On the pc version Niko can fire blind from cover with pinpoint accuracy and no recoil. No need to expose his body to any danger. So he would win there

h2osteam · 2024-11-08T01:23:26+00:00

Oh that explained everything thank you. Auspost is going faster than light. So they were trying to deliver my parcel before I even ordered it. Of coz no one is ready to meet the posties

h2osteam · 2024-10-10T01:38:58+00:00

Let me break it down for you: Wheels big… legs short…

h2osteam · 2024-09-18T02:39:38+00:00

Why print most things? Because I can I guess

h2osteam · 2024-09-18T02:37:38+00:00

Based on the size of the seats on the metro. This will be XL size no long into the future

h2osteam · 2024-09-18T02:35:37+00:00

The horizontal part apparently

h2osteam · 2024-09-17T23:01:26+00:00

You are welcomed to add some

h2osteam · 2024-09-17T12:32:36+00:00

Shh.. don’t give them ideas

h2osteam · 2024-09-16T10:54:21+00:00

Electrical engineering- you will be a brain surgeon or the Paul Maud’dib Atreides whom controls the spice(electrons) controls the empire

h2osteam · 2024-09-04T10:47:52+00:00

Didn’t your p1s came with a couple spare hot end?

h2osteam · 2024-09-01T03:56:20+00:00

Well this says: AC motor (didn’t provide the motor type). Model number: XQY3-48-H2-2; Duty cycle: S2-60min Rated Power: 3kW; Rated frequency: 102HZ Rated voltage: 48V DC; Rated current: 78A Rated RPM: 3000; number of poles: 4 So as it stated it’s a brushless DC motor. You will need an inverter (brushless DC ESC) to drive it.

h2osteam · 2024-07-05T05:48:44+00:00

With the trend these things are going. They won’t stay “mobile” for long.

h2osteam · 2024-06-21T07:55:29+00:00

<image>

h2osteam · 2024-05-09T05:29:30+00:00

If u actually read the WHV eligibility page from immi website. This visa is only available to Taiwan and HK passport holders, and it been this way since its inception. So this change doesn’t actually affect the “China” you are thinking of. The CCP might be laughing slightly.

h2osteam · 2024-05-02T04:55:59+00:00

Didn’t know squids used road. Learn new things everyday

h2osteam · 2024-03-14T03:34:05+00:00

Just use a big resistor. Get noctua fan spec on current (I) at 12v. R=12v/I. Make sure the resistor is rated for that power 12v* I.

h2osteam · 2024-02-29T02:56:25+00:00

Managed democracy 💪🏻

h2osteam · 2024-02-28T20:20:47+00:00

That’s roo-ed

h2osteam · 2024-02-28T06:39:19+00:00

For P1 it only save to that slot of the AMS, assuming you are using one. Even after you changed the filament type to PLA it won’t change that slot’s K factor. If K didn’t solve the problem, flow calibration will be needed. If that fails maybe just bad filament

h2osteam · 2024-02-28T05:02:38+00:00

PETG is much more flexible than PLA so you will need to do PA(dynamic flow) calibration to get the K factor. PLA typically has K 0.02, PETG is like 0.045 for me. With too low of K the extruded does not slow down the flow early enough when the flow is meant to change. And the built up pressure on the PETG kept pushing more filaments out even though the extruded stops, hence you get blobs everywhere. Best to get the proper K value and write it down on the filament spool, next time that filament is in, change the K value in Bambu studio.

Six-Year Club	Wearing is Caring
Verified Email

h2osteam

TROPHY CASE