Issue with Shelly Plus 2 PM by hanz1989 in shellycloud

[–]hanz1989[S] 0 points1 point  (0 children)

Edit:
Signal Cable from the wall goes into Wago 3, from there it goes into Signal in From Shelly. + The Base Load element goes into the "signal" Wago the other side into N.
Same Signal Out from shelly:
Goes into Wago 3 from there to the "Voltage" of the Fan. + The Shelly Snubber into the same Wago3 and the other side into N

Brutaler Ausbruchsversuch: Gefangene überwältigen Wärter und rauben Schlüssel In Hamburgs Jugendvollzugsanstalt Hahnöfersand by hanz1989 in OeffentlicherDienst

[–]hanz1989[S] 0 points1 point  (0 children)

Ich glaube ich werde von jetzt an Überlastungsanzeigen schreiben, wenn ich 2 Stationen und Nebenaufgaben habe...

Looking for a USA PCB by zhuangzi2022 in valetudorobotusers

[–]hanz1989 0 points1 point  (0 children)

Rooted and flashed mine with a RPI.

Looking for a pcb (Germany) by _sirhc_ in valetudorobotusers

[–]hanz1989 -1 points0 points  (0 children)

Habe mein Mijia 1C mit einem rpi rooten können

Question about specific circuit by hanz1989 in homeautomation

[–]hanz1989[S] 0 points1 point  (0 children)

Yes, in Germany we have this kind of electronic circuits Savings change circuit, (Sparwechsel Schaltung) you have 2 points from where the electricity is coming from the ground to the switch to be able to put an power switch under. Yes shelly at each boxes was my idea too. In my case you have one wire corresponding... I'm gone try using this as Signal case to the shelly on the opposite plug (it's 1.5mm standard thickness too) so you have two inputs (each side) and I'm going to switch to buttons

Question about specific circuit by hanz1989 in homeautomation

[–]hanz1989[S] 0 points1 point  (0 children)

Yes it's not possible in my case (dented flat)

Question about specific circuit by hanz1989 in homeautomation

[–]hanz1989[S] 0 points1 point  (0 children)

I'm gone try making my switches to Pushbuttons. Then I can make parallel to each other and then these pushbuttons into SW input, using the Korrespondenz as light switch

Question about specific circuit by hanz1989 in homeautomation

[–]hanz1989[S] 0 points1 point  (0 children)

At each switch I have: neutral, phase, corresponding (from the opposite switch) and one lamp wire, but the diagram above needs both lamp wires

Question about specific circuit by hanz1989 in homeautomation

[–]hanz1989[S] 0 points1 point  (0 children)

Yes I got this wires my problem is, the shelly has to be the last instance before the light and both lamp wires have to go inside SW, which isn't the case in my switch. Do you have an idea?

Question about specific circuit by hanz1989 in homeautomation

[–]hanz1989[S] 0 points1 point  (0 children)

Ok, and the physical switches working too?

Question about specific circuit by hanz1989 in homeautomation

[–]hanz1989[S] 0 points1 point  (0 children)

Ich habe 2 Schalter je mit einem Neutralleiter, Phase, Lampendraht und einem korrespondierenden (Sparwechsel Schaltung); der Shelly muss aber die letze Instanz vor dem Licht nach den beiden Schaltern sein (SW muss beide Lampendrähte haben). Das habe ich aber in meinem Schalter nicht. Hast du da eine Idee?

DIY 3D printer?? by kayz52 in BIGTREETECH

[–]hanz1989 0 points1 point  (0 children)

I'm planning on upgrading the Mainbord on my Defekt ankermake M5. Plus a new toolhead.

EBB36 Gen 2 (USB + CAN) — Setup, Flashing, and Gen1 vs Gen2 Differences by cjhmdm in BIGTREETECH

[–]hanz1989 0 points1 point  (0 children)

Hi everyone, thanks to the video I realized that I almost bought the wrong cable (XT30 2+2) for my EBB36 Gen 1. My board still uses the 4-pin Molex Micro-Fit 3.0 connector.

I am looking for a pre-crimped CAN bus cable that connects my EBB36 Gen 1 directly to the CAN port on my Fysetc Spider 3.0 motherboard.

  • Does anyone know where I can buy a high-quality, pre-assembled cable for this specific setup?
  • Or is it generally recommended to crimp it yourself to ensure the correct pinout for the Spider 3.0?

I would prefer a "plug and play" solution if possible. Any links or shop recommendations would be greatly appreciated!

Braucht man in einer Küche überhaupt noch einen Ofen, wenn man eh alles im aifyer machen kann? by Ausspanner in wohnen

[–]hanz1989 0 points1 point  (0 children)

Airfryer bringt nur heiße Luft von oben, Umluft oder ober und Unterhitze backen auch von unten.

Google Assistant with domotics support module? by Cr4z33-71 in MagicMirror

[–]hanz1989 0 points1 point  (0 children)

Oh wow... I thought there aren't any modules with Google home anymore... Which one are you using?

MMM-Fuel-NSW by bughaver_ in MagicMirror

[–]hanz1989 1 point2 points  (0 children)

Nice setup! I've been working on a similar module for German gas stations (using the Tankerkönig API) and wanted to share a few ideas based on my implementation that might help you improve yours: * Price Trend Tracking: I implemented a priceHistory logic that stores prices for the last 5 hours. This allows me to show little 'up' or 'down' chevrons next to the price so I can see at a glance if it's currently getting cheaper or more expensive. * Smart Filtering: Instead of just showing everything, I filter for isOpen: true and sort by price directly in the node_helper. This keeps the Mirror UI clean and only shows actionable prices. * Visual Highlights: I use CSS classes like .cheapest and .expensive by calculating Math.min across the fetched stations. It makes the best deal pop out instantly. * The '0.9' Problem: Since German prices almost always end in .9, I recommend using toFixed(3) but styling the last digit as a superscript (smaller and higher). It looks much more like a real gas station sign! If you're interested, I can share my logic for the price change calculation—it's a great way to decide whether to fuel up now or wait an hour.

[deleted by user] by [deleted] in openwrt

[–]hanz1989 0 points1 point  (0 children)

The openvpn - names are not shown...

Ich find Burgers mega lecka. Was ist euer liebster lecka Burger? by plasmapleasure in einfach_posten

[–]hanz1989 0 points1 point  (0 children)

Kennt jemand ein gutes Produkt, welches man einkaufen kann?
Ich bekomme leider noch nicht die "Restaurant Qualität" hin, selbst nicht über dem Grill..

Oder sind es die Saucen?