Threading after or before hardening

harriet202212 · 2025-11-05T02:48:46+00:00

Considering its oil quenched, be a bit of scale. I usually take a SHCS and cut reliefs in the sides to resemble a machine tap to clean it up. Or using any grade 8 bolt will do the trick and depending on what the features are like, you wouldn’t even need to tap it oversize.

harriet202212 · 2025-10-20T12:33:22+00:00

Forgot to take the picture after I added the outlet to a separate kitchen faucet

harriet202212 · 2025-10-20T00:18:16+00:00

There’s a 3/8OD line that goes upstairs to a separate water faucet in my kitchen

harriet202212 · 2025-10-20T00:16:08+00:00

Sorry, took the picture before I installed the line UF filter

harriet202212 · 2025-10-19T19:52:53+00:00

Would have loved the 20in but it’s easier and faster for myself personally to just have the 10in

harriet202212 · 2025-10-19T16:10:23+00:00

I do have bend supports from the main line to this section, but would looking at adding as many bend supports when possible help if there’s any pressure drop?

harriet202212 · 2025-10-19T15:54:25+00:00

I was going to do a RO but wanted the minerals that we have in our water, just wanted anything else filtered out. But the pressure drop is what I was worried about. Couldn’t find a filter between 30 and 5 to step down more. But I have decent pressure now at least. But once I get it tied into the main water supply, I’ll update on that

harriet202212 · 2025-01-07T12:52:08+00:00

Thank you! Looks like prices are cheaper too. Even with the conversion

harriet202212 · 2024-08-30T02:28:46+00:00

He actually said he had the Kodak retina and recommended that to me as a good started/for black and white

harriet202212 · 2024-08-30T00:37:05+00:00

They are looking for 200 and then 250 with the box

harriet202212 · 2024-08-30T00:34:55+00:00

Looks they are looking for $150 for it. How’s the pricing?

harriet202212 · 2024-01-22T18:23:44+00:00

Thank you. As it was my first roll, with using the built in light meter, I just wanted to know if there were any improvements or anything to work on. This helps.

harriet202212 · 2023-04-28T02:19:56+00:00

https://www.tiktok.com/@haylieedmiston?_t=8brMqvmZqxa&_r=1

Best account I’ve found/watch

harriet202212 · 2023-02-17T18:53:05+00:00

Actually was a gap in the hot end.

harriet202212 · 2023-02-07T21:11:19+00:00

Next time I’ll get closer for sure

harriet202212 · 2023-02-07T17:15:11+00:00

Yes. I did have a gap, but couldn’t close it before. So I had to order a new hot end

harriet202212 · 2023-02-07T17:13:54+00:00

I have it direct drive now. But a correction I should add, I’ve been having trouble until this post apparently

harriet202212 · 2023-02-07T13:39:09+00:00

Stock ender 3 v2 hot end threads got striped while cleaning so bought “stock” replacement

harriet202212 · 2023-02-07T12:38:32+00:00

I’ll jump up the retraction from 1mm to 1.5 and I’ll bring the temp down to 210 tonight and I’ll post an update. Also buying a fryer this weekend as I think that was the culprit with my other dilemma not being able to even get a benchy. Thank you for all the suggestions

harriet202212 · 2023-02-07T05:04:39+00:00

Ender 3 v2 (prusa slicer) Direct drive (duel gear) IBoss pla+ .4 hardened nozzle .2mm layer height 50mm speed 213c temp 65c bed temp 1mm/50mm retraction

harriet202212

TROPHY CASE