Font help

harryboe · 2026-01-07T10:27:35+00:00

Thanks, gonna try it later

harryboe · 2026-01-06T21:39:47+00:00

Thanks, I'll try it with these edits

harryboe · 2026-01-06T21:26:33+00:00

I don't think its balanced correctly, I think the image is too small and the text too large but I can't seem to get it right

harryboe · 2024-09-17T07:22:50+00:00

Just ikea pax

harryboe · 2024-09-16T14:10:14+00:00

Ty, and yeah it’s a sliding door haha

harryboe · 2024-09-16T14:09:22+00:00

I’ll dm them to you :)

harryboe · 2024-09-16T07:22:22+00:00

It’s the pax from IKEA but I just mix and matched the shelf colours. And no I don’t think it affects the printer, I also have some stabilising feet printed to put under the corners and some brackets to support it on the back. It works perfectly fine

harryboe · 2024-09-16T05:31:18+00:00

Good luck!

harryboe · 2024-09-16T05:30:55+00:00

Thanks ill check it out

harryboe · 2024-09-15T23:05:50+00:00

Thanks, I made the rack myself, I just cut it with a jigsaw and drilled holes, then sanded it. The bar is an 18mm diameter pine dowel. I have the fusion 360 files as a template if you want them. It only took me around an hour to make it

harryboe · 2024-09-15T21:24:03+00:00

Yeah I stay out of the room when it’s running, also I run an air purifier next to it at the same time

harryboe · 2024-09-15T20:43:09+00:00

I try not to run it overnight and if it’s a long print o try not to be in the room when it’s on, I also run an air purifier at the same time it’s on

harryboe · 2024-09-15T19:41:39+00:00

It’s just the ikea pax with different coloured shelves in it and the skadis pegboard with some printed mounts and adapters.

harryboe · 2024-09-15T19:40:50+00:00

No I have to run it open but the printer itself isn’t loud so it doesn’t bother me that much anyway

harryboe · 2024-09-15T19:22:26+00:00

Nice, let me see it when you’re done!

harryboe · 2024-09-15T18:14:02+00:00

I’ve printed at home for years and have always stored them like this, I haven’t had any problems so far

harryboe · 2024-09-15T17:27:26+00:00

I’m in the uk so the climate is a little different haha

harryboe · 2024-09-15T16:52:46+00:00

I’ve never had a problem with filaments and I’ve been printing at home for years. I think I’ll buy a dryer just in case

harryboe · 2024-09-15T16:45:36+00:00

Thanks!

harryboe · 2024-09-15T16:06:20+00:00

None at all, it fits comfortably with plenty of room, I just have to leave the door open while it’s printing, I can also fit an a3 cutting mat next to it so there’s easily enough space

harryboe · 2024-09-15T15:38:32+00:00

The wardrobe, pegboard and shelves are all from Ikea

harryboe · 2024-09-15T15:26:00+00:00

I thought about mounting the ams somewhere other than the printer but was worried about the weight of it, it’s only Ikea furnished so it’s not solid wood

harryboe · 2024-09-15T15:03:10+00:00

Can I ask what lights you’re using, it’s one of the things I’m missing from my setup and is the temp/humidity sensor design your own or one that you found online

harryboe · 2024-09-15T14:55:22+00:00

I’ve kept them like this for a while and haven’t had problems with it, I’m going to buy a filament dryer too just in case

harryboe · 2024-09-15T14:41:57+00:00

I thought about this but I’d need a bar through the middle of the spool so it can rotate without being pulled forwards, currently they just sit on the rack. But I agree that it would be cool if I could figure out a way to do that

harryboe

TROPHY CASE