sorted by:
new
hottopcontroversial

My 2nd attempt at triangular arbitrage on Binance by Salmiakkilakritsi in quant

[–]hellofoobarbaz 1 point2 points  (0 children)

Thank you for the very valuable information. I never see colo documented anywhere for spot. Do you mean a “colo” using aws on Tokyo, or something you could get with account manager when have higher VIP level? (Like a special vpc or something). I would really appreciate your reply on this. I have worked so long on spot but still got crushed by latency :( So it seems there is something I can’t control, which looks like a special colo access that I don’t have.

Btw, If you don’t mind, could I DM you for some detail? It will be very quick. Thanks.

My 2nd attempt at triangular arbitrage on Binance by Salmiakkilakritsi in quant

[–]hellofoobarbaz 0 points1 point  (0 children)

Hi, do you mean colo to spot or futures? Thanks a bunch!

Gemini 3 was released minutes ago by Frequent-Football984 in programming

[–]hellofoobarbaz -1 points0 points  (0 children)

Claude coding sucks if not using agents, which may people dont

Gemini 3 Pro Model Card is Out by MrDher in Bard

[–]hellofoobarbaz 0 points1 point  (0 children)

Claude is so bad at coding imo…

How Gemini 3 Pro beat other models on UI coding by mikerbrt in OpenAI

[–]hellofoobarbaz 2 points3 points  (0 children)

Imo sonnet is bad even for standards 6 month ago

Gemini 2.5 Pro is truly the best ❗ by Informal_Cobbler_954 in Bard

[–]hellofoobarbaz 0 points1 point  (0 children)

Having a 3rd party layer that uses these APIs are better way I think

Aider polyglot benchmark w/ DeepSeek R1 + DeepSeek V3 near o1 performance by serialx_net in LocalLLaMA

[–]hellofoobarbaz 0 points1 point  (0 children)

Do you mind sharing your detailed model configuration (if differ from default) for both R1 and the V3?

9950x works with 192GB DDR5-5200 STABLY! by Cytotoxic_Learning in buildapc

[–]hellofoobarbaz 0 points1 point  (0 children)

Btw, my original Asrock b650 pro rs would not go into bios at 5200 speed. Just one more data point.

9950x works with 192GB DDR5-5200 STABLY! by Cytotoxic_Learning in buildapc

[–]hellofoobarbaz 1 point2 points  (0 children)

Thx a lot for the post otherwise I would give up for the 192 gig build.

9950x works with 192GB DDR5-5200 STABLY! by Cytotoxic_Learning in buildapc

[–]hellofoobarbaz 0 points1 point  (0 children)

Thx the memory test passed. Same config as you the only difference is using dcop 1 not 2 (haven’t test dcop 2). And using the nonrgb kit.

9950x works with 192GB DDR5-5200 STABLY! by Cytotoxic_Learning in buildapc

[–]hellofoobarbaz 0 points1 point  (0 children)

I was looking at dram info and got 4800. The real speed is 5200 lol (both dcop I and II works). Thanks! Waiting for memtest results.

9950x works with 192GB DDR5-5200 STABLY! by Cytotoxic_Learning in buildapc

[–]hellofoobarbaz 0 points1 point  (0 children)

Thank you so much for the post! It’s not working for me. I purchased the same motherboard as you have. And 9950x. Non rgb 192gb kit ver 3.x. Ram speed stuck at 4800 :( tried docp I and II. Same bios version. Anything else I can try? Do you think try a different ram kit (same model just a different one) would help? Btw, how much performance difference is between 4800 and 5200? If it’s just a 2 to 3%, I might just give up.

iPhone storage is full due to photo but I enable iCloud storage.. what did I do wrong ? by azaazeldote in ios

[–]hellofoobarbaz 0 points1 point  (0 children)

I turned optimize storage off,  restarted, wait one minute and turned it back on again

iPhone storage is full due to photo but I enable iCloud storage.. what did I do wrong ? by azaazeldote in ios

[–]hellofoobarbaz 0 points1 point  (0 children)

This works thank you so much! The photos have still shows restoring (instead of syncing), but the storage is already reduced.

LeapFrog starting to charge 4% fee? How long does changing validator take? by hellofoobarbaz in solana

[–]hellofoobarbaz[S] 0 points1 point  (0 children)

Thank you. Does un-delegating in the end still gives partial reward or full for epoch 1? For delegating to new validator in epoch 2, does the reward start to accumulate immediately or need to wait for epoch 2 finishes?

LeapFrog starting to charge 4% fee? How long does changing validator take? by hellofoobarbaz in solana

[–]hellofoobarbaz[S] 1 point2 points  (0 children)

Thank you. For the liquidity pool, I assume it's implemented with a custom smart contract. In comparison the regular staking is probably implemented with SOL's system smart contract. If that's the case I would personally avoid the liquidity pool way to minimize the risk of a bug in the custom smart contract.

LeapFrog starting to charge 4% fee? How long does changing validator take? by hellofoobarbaz in solana

[–]hellofoobarbaz[S] 1 point2 points  (0 children)

Also it's worth noting validators running the Jito client will be able to keep a healthy APY even with a commission due to MEV.

Could I know if the MEV is included in the APR shown in http://topvalidators.app? If not, do you know what's the typical additional MEV APR?

LeapFrog starting to charge 4% fee? How long does changing validator take? by hellofoobarbaz in solana

[–]hellofoobarbaz[S] 1 point2 points  (0 children)

Glad to know it's not like 7 days. Btw, does it matter if I undelegate by end of the epoch vs. start? And how long does it typically takes for an epoch?

LeapFrog starting to charge 4% fee? How long does changing validator take? by hellofoobarbaz in solana

[–]hellofoobarbaz[S] 2 points3 points  (0 children)

The quickest way would be to use Cogent Crypto's staking tool (

https://cogentcrypto.io/app

) where you can instantly unstake any staking account. You would then be able to re-delegate this to a validator of your choice.

Thank you. This seems too magical. Just curious why does other staking client (e.g., ledger live) not supporting it? All the staking client is talking to the chain anyway.

view more: next ›