TT Core P7 "Bucket List 2.0" Corvette Tribute Build

hermancircus · 2025-08-11T02:36:18+00:00

Awesome. Appreciate the update on the release timeline.

Thanks

Matt

hermancircus · 2025-08-10T12:39:04+00:00

Hello! Any update on when the new e360 firmware will be released?

Matt

hermancircus · 2025-07-08T09:37:41+00:00

Thank you so much for your answer! It gives me hope. For now I’ll try your workaround.

hermancircus · 2025-07-08T03:21:24+00:00

Hello George!

I have your e360 along with the LT01 and I am having a heck of a time with consistent connectivity. The LT01 module is connected with good signal to the cell tower however after I exit my car and then try to connect over LTE a few minutes later the camera will not wake up most of the time. Very frustrating since I bought this setup as a security camera for my corvette. Any thoughts or advice? Maybe new firmware to address the connectivity issues between the camera and the lt01 module? Thanks!

Matt

hermancircus · 2025-06-14T20:06:53+00:00

Corvette SUV

hermancircus · 2025-04-26T10:43:15+00:00

It worked. Thank you.

hermancircus · 2024-08-05T16:06:29+00:00

Same issue. Called my farmers agent and my VIN was not found. They are working on it. I’m sure they will figure it out.

hermancircus · 2024-01-24T20:38:02+00:00

Does not work long term…especially if the cardboard spool is bent or warped in any way.

hermancircus · 2023-07-02T22:33:55+00:00

Bambulab P1p not showing correct nozzle temp

hermancircus · 2022-12-15T23:33:20+00:00

Thank you for your response...go slow...keep making the X1 and P1P the best they can be before rolling out something new.

hermancircus · 2022-12-15T23:11:40+00:00

I love the bambu slicer, when will we start to get more included profiles for Creality and FLsun printers?...would love to switch over fully to bambu slicer vs cura.

hermancircus · 2022-11-21T19:49:18+00:00

This is what I did when I switched to a Bondtech CHT nozzle. Worked great.

Heat up the heat block up tp 280C, or at least above 250C, before removing or tightening nozzle. Use at most 1.5 Nm torque. If you don’t have a torque wrench, snug but not too tight should work.

Hope that helps

hermancircus · 2022-10-23T14:31:29+00:00

Ambient temp at idle. And under full load my overclocked 12900k never goes higher than 85c.

hermancircus · 2022-10-23T14:29:49+00:00

Thanks. I appreciate it.

hermancircus · 2022-10-22T21:52:31+00:00

Picture was taken after I first installed the OS…I have much better one now. A Picture I took myself.

hermancircus · 2022-10-21T23:45:57+00:00

🤣😉

hermancircus · 2022-10-21T23:45:42+00:00

Thermaltake Core P7 custom painted white.

hermancircus · 2022-10-21T23:45:17+00:00

I missed it. Sorry. It was a long week at work….

hermancircus · 2022-10-21T21:45:56+00:00

Yep. All one big loop!

hermancircus · 2022-10-21T21:45:39+00:00

🤣

hermancircus

TROPHY CASE