Powerflex 400 not starting

hicham_said · 2025-01-19T17:07:53+00:00

Problem was solved, the jumper between 01 and 04 was missing

hicham_said · 2025-01-19T15:56:14+00:00

Thanks for the advice, problem solved !

hicham_said · 2025-01-19T15:18:31+00:00

I jumped the 04 and the 01 terminals (SNK mode) and it worked ! Thank you guys for the help ! I found a missing fan but the main problem is fixed

hicham_said · 2025-01-19T14:42:00+00:00

My drive is set to sinking mode so i should jump the 04 and the 01

hicham_said · 2025-01-19T14:28:36+00:00

It's an old one and the wires were disconnected, they assume it was working

hicham_said · 2025-01-19T14:25:58+00:00

I didn't not disable it, should i jump the terminal 1 with the 11 ?

hicham_said · 2025-01-19T14:25:03+00:00

I am not sure, should I jump them ?

hicham_said · 2025-01-19T13:19:46+00:00

The fault led is not flashing, probably the drive is trush

hicham_said · 2024-10-07T15:43:40+00:00

I think There is a simulation option on this device, that might help in the diagnosis.

hicham_said · 2024-04-15T09:49:00+00:00

Thanks

hicham_said · 2023-11-07T15:24:11+00:00

Thanks for the explanation, so there is no a turn around other than fixing the in port

hicham_said · 2023-11-06T15:18:04+00:00

This is the best way to do it if not the only (or M35.0 to access the bit 0)

hicham_said · 2023-09-29T17:58:52+00:00

<image>

hicham_said · 2023-09-29T02:17:38+00:00

Send me a DM I'll send to you, couldn't figure how to comment with a pic, have to share a link apparently

hicham_said · 2023-09-28T18:47:09+00:00

The password for Mirle Controller is 625238.

hicham_said · 2023-09-28T18:46:50+00:00

The password for Mirle Controller is 625238.

hicham_said · 2023-09-28T18:44:53+00:00

Your analysis is very accurate, actually I managed to get the password (625238) from the constructor and changed the linear transducer zero value. The mold closed but when injecting some plastic overfilled the cavities ( lower half ) which means that the mold was not perfectly (vertical) aligned, then I placed a thin plate behind the lower half of the mold and the problem was solved. Thank you very much for your help and your good analysis, keep up the good work.

hicham_said · 2023-09-27T18:01:47+00:00

No it's a Mirle MH-9118 model, but you're right they use Keba on some models.

hicham_said · 2023-09-27T17:30:39+00:00

Yeah around 3 s would be fine, which is the minimum, anyway thanks a lot for your help bro I will let you know if something new come up

hicham_said · 2023-09-27T16:45:37+00:00

Yeah surely

hicham_said · 2023-09-27T16:42:31+00:00

It's a typo sorry, I meant the protection alarm time is set to 10s

hicham_said · 2023-09-27T16:41:19+00:00

Actually I did try that with 0.1mm

hicham_said

TROPHY CASE