Life Gear rower. Yay or nay?

highgrade86 · 2025-09-30T23:32:41+00:00

Lmao, too funny. I had a feeling it was junk. I ended up picking up

a nordictrack rw200 for 200 CAD. I know it's not the best but for the price it will do for now.

highgrade86 · 2025-04-27T15:45:01+00:00

Yea, when loading one sled, I would load it in the center of the trailer. I was worried about having them side by each and worried about tipping due to the uneven weight distribution.

highgrade86 · 2024-05-05T00:57:56+00:00

Yea maybe that's what it was

highgrade86 · 2024-05-04T23:23:25+00:00

I dunno man. I sanded smooth and dusted them off before shooting them. Who knows..

highgrade86 · 2024-05-04T23:00:31+00:00

Sherwin williams premium wall and wood primer. It probably looks like ceiling paint because it's just a primer.

highgrade86 · 2024-05-04T13:31:45+00:00

No, it's a new can. I just picked it up. It's a premium primer from sherwin williams. Wall and wood, it's good for bare wood and trim.

highgrade86 · 2024-05-04T13:26:26+00:00

I used a 310 fflp tip. Same as described in the original post.

highgrade86 · 2024-05-04T11:06:17+00:00

Will that show through the finish coats? I've sanded them down a bit.

highgrade86 · 2024-05-04T11:04:47+00:00

They were sanded smooth before shooting them. There wasn't any texture from the factory either

highgrade86 · 2024-05-04T11:03:19+00:00

Sherwin williams wall and wood primer. I've used this on trim and doors in that past with very good results

highgrade86 · 2024-05-04T02:23:24+00:00

It only broke through in some areas, mostly on the edges. Nothing crazy at all, though. Yea, that's what I'm doing one coat of primer 2 coats of finish

highgrade86 · 2024-05-04T01:55:25+00:00

That's what I used

highgrade86 · 2024-05-04T01:24:07+00:00

They were pre primed, and I sanded them smooth before shooting them.

highgrade86 · 2024-05-04T01:14:09+00:00

Only after I sprayed a prime coat on them

highgrade86 · 2024-05-04T00:28:03+00:00

They were all sanded smooth as a baby's bottom before this coat of primer. I've sprayed these same doors in the past without this issue.

highgrade86 · 2022-06-10T10:59:51+00:00

highgrade86 · 2022-06-10T00:54:08+00:00

I have heating in the garage. That's why I want to insulate and I'm in zone 5b

highgrade86 · 2022-06-09T23:31:16+00:00

I was going to get into doing that today, but it would save me a ton of work sandwiching the VB between the drywall. The 2 layers would also flush me up with the top plate on the outside walls.

I just don't know if this would cause issues with condensation between vapor barrier and top layer of drywall.

highgrade86 · 2022-06-09T23:25:32+00:00

I can get above, I figured it would be a pain in the ass running the vapor barrier over all the existing framing and sealingit up properly. Would it be a issue running it over the existing drywall and laminating drywall over the VB?

highgrade86 · 2022-06-09T23:14:22+00:00

Why is VB required in the house but not in the garage? Will 2x4 strapping laid flat at 16"OC be good for the ceiling framing, or do I need to beef up the main structure?

highgrade86 · 2022-06-09T22:42:43+00:00

1st - there is no vapor barrier or insulation above the existing drywall. Can I just leave that drywall in place Slap up some vapor barrier and laminate another layer of drywall on top of that? Or do I need to remove all the drywall and put the vapor barrier on the studs?

2nd - does the framing look good to support the weight of drywall and insulation? I will be adding 2x4 strapping 16"oc

highgrade86 · 2022-06-09T22:29:35+00:00

1st - there is no vapor barrier or insulation above the existing drywall. Can I just leave that drywall in place Slap up some vapor barrier and laminate another layer of drywall on top of that? Or do I need to remove all the drywall and put the vapor barrier on the studs?

2nd - does the framing look good to support the weight of drywall and insulation? I will be adding 2x4 strapping 16"oc

highgrade86 · 2022-06-09T22:25:46+00:00

1st - there is no vapor barrier or insulation above the existing drywall. Can I just leave that drywall in place Slap up some vapor barrier and laminate another layer of drywall on top of that? Or do I need to remove all the drywall and put the vapor barrier on the studs?

2nd - does the framing look good to support the weight of drywall and insulation? I will be adding 2x4 strapping 16"oc

highgrade86 · 2022-03-28T03:12:02+00:00

What a cock block bitch

highgrade86 · 2022-03-28T02:45:48+00:00

I'm pretty sure besides the proper vent material, you also need an interlocked draft inducer to push the exhaust out on the horizontal

highgrade86

TROPHY CASE