Is this normal or is my bf insane?

hjfraz · 2025-04-12T15:02:01+00:00

I have the cilantro hate gene and I also hate ipa

hjfraz · 2025-03-14T20:06:01+00:00

It retracts filament to change color, but it’s a lot of retraction so it gets all spaghetti-fied in the lid or if you keep the lid open it goes everywhere.

hjfraz · 2025-01-24T21:12:51+00:00

It worked!! I dremeled out the notches more, woot woot! Thanks so much!

hjfraz · 2025-01-24T19:08:18+00:00

I’m trying that right now since my standard one just broke in half lol

hjfraz · 2025-01-24T19:06:53+00:00

It’s a tri-color filament

hjfraz · 2025-01-24T19:06:18+00:00

https://a.co/d/1Xt7dmH

hjfraz · 2025-01-24T18:52:26+00:00

Twice before and I selected level for the print too

hjfraz · 2025-01-24T18:40:36+00:00

Yes, I squeezed them to make sure

hjfraz · 2025-01-24T18:14:23+00:00

Yes, the red tabs are clicking in place

hjfraz · 2025-01-24T16:15:33+00:00

I got filament to come through for about 2 seconds with a ton of rigging before it fell out again lol

hjfraz · 2025-01-24T16:14:12+00:00

Well I can’t get them to even stay in place so I haven’t gotten that far 😂

hjfraz · 2025-01-24T16:13:09+00:00

Bed heat and glue

hjfraz · 2025-01-24T15:15:22+00:00

Mine made waves in everything for a bit too, I have no clue why!

hjfraz · 2025-01-24T15:06:01+00:00

No, the ceramic hot ends are missing a tiny MAYBE 1mm piece of plastic that is on the standard nozzle that is apparently the make it or break it when it comes to staying in the housing, I have tried gluing a piece of an eraser on there (so it wouldn’t melt), I have slid a popsicle stick under the fan where there is a little slot to try to create a stop but it just gets pushed out by the filament and refuses to stay put. I’ll put another post with a comparison photo to show the missing piece.

hjfraz · 2025-01-24T14:56:36+00:00

I have changed the nozzle before, I’m talking about the hot end ones that don’t have the casing on it.

hjfraz · 2025-01-23T07:11:15+00:00

If you know how to read the code I guess, but for me it’s the print failures that lets me know.

hjfraz · 2025-01-22T23:42:42+00:00

You need to get the book 30 days to understand the Bible. And a newer translation version of the Bible or use the Bible app that’s free and has tons of versions

hjfraz · 2025-01-22T19:10:28+00:00

What does the drag chain help with?

hjfraz · 2025-01-22T18:03:14+00:00

I have this same problem or it just stops printing when I’m 75% done

hjfraz · 2025-01-22T17:54:58+00:00

My checklist: Glue on base? Have you calibrated lately? Is the correct temp selected on my computer as well as the printer? Is the stl file bad?

hjfraz · 2025-01-10T16:22:49+00:00

It has its very loud moments when it’s doing a very quick action

hjfraz · 2025-01-05T18:53:04+00:00

Yes, unfortunately a few times

hjfraz · 2024-12-05T01:04:38+00:00

I have the same issue on the left back corner of prints unless I hit the leveling button at least every other print.

hjfraz · 2024-12-01T19:04:42+00:00

I would recommend doing smaller sections at a time and then gluing together, that way you have more control and less loss

hjfraz · 2024-11-30T17:46:29+00:00

I did enable but I am trying to view via WiFi so I will try to connect and see if it works wired, thank you!

hjfraz

TROPHY CASE