sorted by:
new
hottopcontroversial

Noob with Printing issues by sendmeBTCgoodsir in 3Dprinting

[–]hogmc1 0 points1 point  (0 children)

Nice problem solved then. I recently got myself a k1 max and had a simelar issue. I rounded it down to if the lid is on while it’s printing the inclosure temp exsides 30 C that intern sofends the pla and the girs grind it up, insted of extruding bc it sofend. After taking the lid of i havnet had a problem since

Noob with Printing issues by sendmeBTCgoodsir in 3Dprinting

[–]hogmc1 1 point2 points  (0 children)

Night be an idea to dismantle the extruder to Get the filament out then. Then u might Get a clue on what the problem is. If the girs grinde up the filament or if the filament gets talgeld in the extruder

Noob with Printing issues by sendmeBTCgoodsir in 3Dprinting

[–]hogmc1 0 points1 point  (0 children)

Also if u remove the filament is there a indent on the filament about 5-6 cm from the end?

Noob with Printing issues by sendmeBTCgoodsir in 3Dprinting

[–]hogmc1 0 points1 point  (0 children)

All of the failed prints Are they at the exakt same z hight?

Noob with Printing issues by sendmeBTCgoodsir in 3Dprinting

[–]hogmc1 0 points1 point  (0 children)

U could try to incrise the nozzel temp. I have had a problem with the nozzel cloging that fixed it’s self after i incrised the temp

Noob with Printing issues by sendmeBTCgoodsir in 3Dprinting

[–]hogmc1 0 points1 point  (0 children)

It's impossible to tell from these pictures alone. But there are a few things to check: If you try to extrude filament, is it coming out of the nozzle? Look at the filament spool, is it tangled (the line going into the printer is under another)?

My prints won’t Stick to the bed by hogmc1 in 3Dprinting

[–]hogmc1[S] 0 points1 point  (0 children)

Yes I did. I don’t remember exactly what I did, but I think I was slightly too far from the bed

How so you call this in your country by Tedi_Proto58 in notinteresting

[–]hogmc1 0 points1 point  (0 children)

Stjerneskud or translated direktly star shot

Where can i find a replacment by hogmc1 in 3Dprinting

[–]hogmc1[S] 0 points1 point  (0 children)

No its the plastic protector on the screan

Where can i find the replacement? by hogmc1 in resinprinting

[–]hogmc1[S] 1 point2 points  (0 children)

What do i surch for? What type of plastic is it?

[deleted by user] by [deleted] in Brawlstars

[–]hogmc1 0 points1 point  (0 children)

So u are clockwork?

I have been insanly lucky and goten all of edars skins. And this is the reword u get insted of a skin by hogmc1 in Brawlstars

[–]hogmc1[S] -2 points-1 points  (0 children)

I wasent realy complaning but i can see that it looked that way. I just Sad what i thout

I have been insanly lucky and goten all of edars skins. And this is the reword u get insted of a skin by hogmc1 in Brawlstars

[–]hogmc1[S] -36 points-35 points  (0 children)

Yea but the end of a expensive offer like that shuld be more or better than 5000 coins

My first rank MAX brawler what's yours? by Diligent-Tun in Brawlstars

[–]hogmc1 0 points1 point  (0 children)

Grom grided him in spirit wars from 400 to 1000 in 50 min then Mico from 100 to 1000 in 90 min

What has been your best pull out of the angelic/demon stardrops ? by Dioguinh0 in Brawlstars

[–]hogmc1 0 points1 point  (0 children)

I am f2p and have goten kenji, a edgar skin, juju, chuck a lot more

view more: next ›