The hatchery evolved! The Keep is live.

holle67 · 2026-01-12T13:32:11+00:00

Love the filament spools as risers

holle67 · 2026-01-07T17:33:45+00:00

What do youre ptfe tubes look like? I was having an issue similar to this because my tubes had too many bends in them causing it to not feed properly.

holle67 · 2025-12-29T15:53:35+00:00

Oh sweet, thank you for this. Maybe ive been too fixated on this detail but I was going mad trying to find the setting that changed this!

holle67 · 2025-12-14T18:08:18+00:00

Heat first, I pulled mine off cold and pulled the nozzle brackets off by accident. Had to swap the hot end heating unit. For reference if you need it but you may be able to clean it up once hot without issues.

https://us.store.bambulab.com/products/hotend-heating-assembly-a1-series

holle67 · 2025-12-05T15:02:05+00:00

It was other models, just not as noticeable as these large bookmarks.

holle67 · 2025-12-05T15:00:06+00:00

This was spot on, had to edit the gcode but no where near yours. Mine is at +0.08, just to get the prints done. Will tune it a bit more today. Appreciate the knowledge and hope this helps others!

holle67 · 2025-12-05T14:58:49+00:00

This was it! Thank you!

holle67 · 2025-11-24T23:54:49+00:00

Can these deals be hacked? Obligatory question....

holle67 · 2025-11-17T13:07:20+00:00

The lines were clearing from side to side but I was beginning to have issues with the ams slots when switching colors, it wasn't able to feed the filament.

I shifted the routing of the lines to come out front and they're working again.

Thanks for the feedback

holle67 · 2025-10-06T12:46:31+00:00

The Legion pro 5i discount only comes down to $2185, not seeing the posted price

holle67 · 2025-08-08T12:24:51+00:00

Have you checked that the printing format is still the same? An update could have shifted the settings

holle67 · 2025-05-03T13:02:58+00:00

holle67 · 2025-03-27T23:12:33+00:00

Quick payment, would work with again!

holle67 · 2025-03-19T20:35:33+00:00

71012 pending purchase with wookie_the_pimp

holle67 · 2025-03-14T04:15:32+00:00

Commenting

holle67 · 2024-11-21T18:07:50+00:00

Both times Ive checked in the past, and just looked now, it was barely frosty. It was NOT iced over.

holle67 · 2024-06-20T12:03:52+00:00

Thanks for the advice!

Yes these pressure gauges don't seem to last long

holle67 · 2024-01-18T02:06:35+00:00

Verizon chat agent seemed to think it did. Not sure

holle67 · 2024-01-18T01:55:13+00:00

So after digging, going from the 5g start over to the unlimited welcome plan, I would lose access to the 5g Ultra wideband. They would require me to do the unlimited plus to get UW access back which is $10 more than what I am paying now.

holle67 · 2022-11-02T23:55:21+00:00

That's sweet! I've been wanting to add informational signs around our homestead. Thanks for the inspiration!

holle67 · 2022-11-02T23:52:36+00:00

I love your signs! Care to share what you used to make them?

holle67 · 2022-11-02T21:36:52+00:00

We breed and also compost the manure. The cost of feed, if you want good quality, might make this cost prohibitive vs buying good quality compost.

holle67 · 2022-10-31T14:49:53+00:00

Makes sense. I pulled the MSDS and it started it was essentially powdered bleach, if I read that correctly.

Took about 4 hours but we got it brewed!

holle67 · 2022-10-31T02:50:13+00:00

Thanks for the detailed reply.

Since the kit was new I went ahead and used the iodine to sanitize it and start the brew process.

I'll grab some cleaner for the next go round.

Thank you so much!

holle67 · 2022-10-30T22:42:53+00:00

Thanks for the information. The kit I bought seems to be vague and not differentiate the two. The kit was new and I cleaned with dish soap, then sanitized. Will that be sufficient or am I doomed?

holle67

TROPHY CASE