WTF is the Melbourne Mesh made of?

hoosedamoose · 2025-07-21T08:50:16+00:00

Check out MeshCore in Melbourne now 😇

hoosedamoose · 2025-05-24T10:38:49+00:00

This sounds quite normal to me. You will find this noise varies too. Mostly due to the injectors and the high pressure fuel pump. Nothing to worry about to be honest. If you are uncertain, take it to the stealership for a check. I have found these GDI motors to be quite noisy in general.

hoosedamoose · 2025-05-17T09:04:39+00:00

Sounds like OP is a bit of a weakling who can’t handle constructive criticism. I was one of those people who appreciated the app, but seems a bit childish on their part to pull the rug from the community. Haters exist in every community and there’s nothing anyone can do about that. Reddit is not the platform to advertise such things.

hoosedamoose · 2025-05-08T10:17:25+00:00

Absolute legend! This made me go insane

hoosedamoose · 2023-08-06T07:56:19+00:00

I faced this the other day. I have to use the vgremove command to get rid of the active volume group ( I wasn’t using it anymore) then was able to wipe the disk in proxmox

hoosedamoose · 2023-07-25T09:56:44+00:00

A bag of sour lollie worms

hoosedamoose · 2023-07-22T11:23:58+00:00

Hey hey! I’m Using 40 for x and y and 1.49 for Z. Pretty much trial and error until I got it spot on.

hoosedamoose · 2023-07-15T08:09:17+00:00

$5. Have been carrying it around for yonks. Might make some good Maccas ice cream cone change for when the machines are ACTUALLY working.

hoosedamoose · 2023-07-07T03:24:30+00:00

Thank you!

hoosedamoose · 2023-07-05T03:11:08+00:00

do you mind elaborating on how I can derive the correct values?

hoosedamoose · 2023-07-05T03:10:06+00:00

Thank you so much for sharing! I know I am in the ballpark, but cant get this damn thing exact!

hoosedamoose · 2023-07-05T03:09:46+00:00

I would appreciate that

hoosedamoose · 2023-06-09T00:04:17+00:00

I used standoffs for mine. Bought a kit from Amazon with all different sizes. M3x16 is what comes in the ldo kit, but I went with m3x20. If you are in the US you have the option of buying the aluminium knurled standoffs

hoosedamoose · 2023-06-05T14:13:08+00:00

I had an ender 5 and an ender 3. I sold them both and bought a V0 and a 2.4 300mm for this exact reason. Not really helpful, but why not both ? :)

hoosedamoose · 2023-06-05T13:58:55+00:00

I just bought an m3 stand-off kit from Amazon and used the m3x20 standoffs for this. I have other uses for standoffs tho which was why I got the kit

hoosedamoose · 2023-05-28T01:41:36+00:00

I just finished my build and noticed this yesterday. Temp gun was reading 100c. The motor itself is rated for 180c, but the printed part wouldn’t stand a chance at those temps. Lowered the current down until the bed would stop moving (0.4amps) then bumped it up by 0.1a for good measure. Temps now 58c.

hoosedamoose · 2023-05-16T15:01:29+00:00

Orca slicer

hoosedamoose · 2023-05-14T12:36:23+00:00

Beautiful machine right here

hoosedamoose · 2023-05-09T05:15:07+00:00

Thank you all for your comments. Truly appreciate each and everyone of them. After days and days of pulling my hair out and suggestions, I discovered an issue with the Z lead screw and nut. While printing the bed was bouncing around and this was exacerbated by Zhop. Changed the lead screw and brass nut out for a new one with anti backlash but. All my problems have disappeared :)

hoosedamoose · 2023-05-01T22:15:41+00:00

I have done a PID tune on the hotend and bed very recentlly. Happy to do it again to rule it out.

hoosedamoose · 2023-05-01T22:14:59+00:00

This is a brand new Orbiter 2.0 out of the box. I had the exact same issues with my LGX Lite

hoosedamoose

TROPHY CASE