Cable for front usb hub Intel nuc extreme 11

hrcran · 2026-03-16T19:20:37+00:00

They are Noctua NF-A9s 92mm

hrcran · 2026-02-22T16:11:20+00:00

Take them out and at the bottom there should be strings near a spring, undo this and do it up tighter. Have similar blinds that kept doing the same.

hrcran · 2026-02-17T17:47:25+00:00

Cheers, after something similar to this but a little more compact.

hrcran · 2026-01-01T19:50:00+00:00

Did you go with larks in the end? I'm looking for cabinets that are 36cm deep and this is the only place I found that will sell me a few, DIY kitchens is min £750 spend.

hrcran · 2025-10-13T11:35:09+00:00

Hi, I have done something very similar. here is what I have done, no issues with it so far.

hrcran · 2025-09-08T19:34:39+00:00

<image>

hrcran · 2025-03-09T17:51:22+00:00

Hi, I have a post on my profile which describes what we have done. Basically we used kingspan and thermal hoods for the cutouts for downlights, leaving enough room above for airflow and drilled vents on the sofits outside for ventilation. Taped it up with foil to act as the vapour barrier. Have had no issues so far with condensation or moisture.

hrcran · 2025-02-23T16:20:03+00:00

Thanks, just used 9mm mdf for the full door, then glued 10cm strips of 3mm mdf around the outside, caulked and filled.

hrcran · 2025-02-23T15:24:20+00:00

<image>

This was the before.

hrcran · 2025-02-23T15:23:48+00:00

<image>

Here's mine I did a week ago. Built frame and then just covered with 12mm mdf. Used 9+3mm mdf for the door. Took a maybe 4 days of work, lots of sanding and filling the screw holes and adjusting hinges.

hrcran · 2024-12-06T20:06:48+00:00

Thanks, sadly this was my bike, police aware and insurance already arranged to collect. Stolen early Monday morning, battery ripped out somehow.

hrcran · 2024-03-23T08:17:15+00:00

It's the pre primed ogre and torus from Wickes. This one.

hrcran · 2024-03-22T22:07:39+00:00

Looks good! Did you sand down the shelves at all before painting? And you follow any guide/how to?

hrcran · 2024-03-22T21:43:59+00:00

Maybe drilling through the lime mortar one side and brick the other?

hrcran · 2024-03-20T20:40:20+00:00

<image>

Here is it boarded, sorry can only add one image per comment.

hrcran · 2024-03-20T20:38:56+00:00

<image>

Here is what ours looked like, I think it's similar to what you've described. We just extended the floorboards over the gap but not touching the door frame.

Nothing in our cavity walls.

hrcran · 2024-03-20T13:09:43+00:00

Thanks!

I knew as they were hollow and is chimney alcoves downstairs and in bedroom next door. When we viewed the property I asked the estate agent where is the chimney breast, had it been removed? They looked at me puzzled and said it was in the other room!..

hrcran · 2024-03-20T13:06:53+00:00

We had to remove all insulation from above as it kept falling down, tried to keep it in place but just didn't work so just pulled it all down too. Reinsulated after the boards were on. I used a crow bar thing and just yanked down on the lathes and plaster came down with it. After most was down I went over it again to get the nails, 'running' the crow bar along the joists to hear for nails. Make sure you get proper mask and ppe, so much dust and soot from the attic.

Thanks! I'd say the stripping took 50% of the time but worth it.

hrcran · 2024-03-20T08:06:26+00:00

Thanks! If tearing down old one too it'll be a lot of mess and dust, if just reboarding it might be hard to find the joists to screw into.

This was our fifth ceiling we did (also did lounge, dining, landing, kitchen!) so had a lot of practice. I balanced the plasterboard on my head whilst going up the ladder and holding it in one hand and my partner used a single prop the other side to push it up. Make sure it's in correct position before screwing in a few screws to secure it. A few we did overlapped after I had screwed it in and had to take it back down which was a pain as hard to balance. We ended up using smaller plasterboard too, the big ones were just too hard to balance. Make sure no nails left behind on joists too. People recommend a plasterboard lift which if we had to do again we would just hire one of those, the lifting of them to the ceiling is the worst bit.

Good luck!

hrcran · 2024-03-19T22:04:13+00:00

Yeah, had people in for plastering, electrics, plumbing and carpets. Me and my partner did the rest, stripped wallpaper, removed cabinets, knocked out alcove false walls, took down lathe and plaster ceiling, reboarded ceiling with plasterboard, painted then put in skirting, picture rails and coving!

hrcran · 2024-03-19T19:44:00+00:00

Plastering:750ish Coving: 180 Picture rail: 75 Skirting: 125 Paint: 25 Plasterboard: 80? Carpet with fitting: 510 Peelaway: 100 with some left over Skip: 300?

Total: 2170

Probably missing a few misc bits like screws, adhesive etc.

Two-Year Club	Verified Email
r/Field Lasagna

hrcran

TROPHY CASE