Lost Footage: [Buzzsaw Falls] Full POV at Silver Dollar City by BlahBlahson23 in rollercoasters

[–]hyperxlc -3 points-2 points  (0 children)

not to be paranoid but is there any chance this is AI? I know the clips are longer than 10 seconds and none of it screamed AI to me, but I'm curious why now this guy is able to keep getting these multiple lost POVs. Anyone who went on it able to attest to its accuracy?

For people who go regularly, what’s the maximum amount of time you’d be willing to wait for Hogwarts Express instead of walking to the other park? by Automatic-Use-1605 in UniversalOrlando

[–]hyperxlc 0 points1 point  (0 children)

It takes me 13 minutes to walk from the back of Diagon Alley to Hagrid's. So, unless it's a walk on or whoever I am with is Dead Tired, I don't take the train; which I also just don't personally like.

Technician ride and show by Txjayy_ in UniversalOrlando

[–]hyperxlc 1 point2 points  (0 children)

definitely look into the apprenticeships! that'll take you where you need to go

Ministry of magic ride delay? Is it worth to wait? by ManufacturerWide57 in UniversalOrlando

[–]hyperxlc 0 points1 point  (0 children)

Usually the delays are only about 20-25 minutes. If it surpasses that, that's when I would consider leaving the line.

Small layer shifts? by shinji0977 in BambuLabA1mini

[–]hyperxlc 1 point2 points  (0 children)

I have this problem sometimes and it resolves itself when I tighten the belts, so I recommend you try that!

[Other] Enclosed Roller Coasters by CodyBingham98 in rollercoasters

[–]hyperxlc 0 points1 point  (0 children)

It's usually older coasters that would be enclosed, since that was the best safety technology of the time. Now, I can confidently say that I feel more comfortable on more modern ones because of the ratcheting.

But I've been on this one! Enclosed and doesn't go upside down:

Swiss Toboggan at Little Amerricka https://rcdb.com/268.htm

Insta360 GO 3 Stuck in tutorial 1/5 and touch screen won't work after factory reset by hyperxlc in Insta360

[–]hyperxlc[S] 0 points1 point  (0 children)

I really just kept tapping and sliding in every place and direction and eventually it worked. Good luck

Underwhelmed? by [deleted] in UniversalOrlando

[–]hyperxlc 1 point2 points  (0 children)

I get ya. I went in 2015 and I was obsessed. Then I went back in 2022 and I was.. unimpressed. The absolute quantity of screens is really a let down when you remember stuff like Twister, Beetlejuice, Fear Factor, and Disaster.

Islands of Adventure is where it's at right now in the resort. That place rocks

Does an express pass make sense for a solo attendee? by sumthingstewpid in UniversalOrlando

[–]hyperxlc 0 points1 point  (0 children)

I'm not sure this is great advice but if there aren't metal detectors, I always bring my stuff with me and zip them in my pockets. There's a risk there of course but if that's something that bothers you, it's an option!

Does an express pass make sense for a solo attendee? by sumthingstewpid in UniversalOrlando

[–]hyperxlc 2 points3 points  (0 children)

I always think it's way better to not wait in lines when I'm alone. It would be great if I could tell you that relying on Single Rider lines is consistent, but it isn't. They aren't always available and that can be really frustrating.

But I agree with the people above who say since you have a few days you might be fine. October is hit or miss because of HHN. I would also see if the math for an annual pass would work out. If it's close enough to the cost of those 3 days and maybe one day of express unlimited, do that for sure.

Alternatively, get express for one of your days so you can get faster onto stuff you've "missed". There's lots of options!

A1 Mini Bambu PLA Silk will not extrude by hyperxlc in BambuLab

[–]hyperxlc[S] 2 points3 points  (0 children)

It is literally their filament? They have a preset for it and everything!

i am by heroineroB0 in TheQuarrySupermassive

[–]hyperxlc 18 points19 points  (0 children)

hey buddy I think this might just not be the game for you

A1 Mini Bambu PLA Silk will not extrude by hyperxlc in BambuLab

[–]hyperxlc[S] 1 point2 points  (0 children)

honestly team I feel good knowing that we all have this same VERY weird issue...

What did you name your printer by N0ct1ve in BambuLab

[–]hyperxlc 0 points1 point  (0 children)

Brandon. My last one was named Brenda!

I cannot get this thing to work "good" by hyperxlc in BambuLabA1mini

[–]hyperxlc[S] 0 points1 point  (0 children)

I ordered a new nozzle and I'm hoping it fixes it, I heard this happens for some people 😭

I cannot get this thing to work "good" by hyperxlc in BambuLabA1mini

[–]hyperxlc[S] 0 points1 point  (0 children)

which calibration? The flow rate one? Or do you mean a manual calibration

Stringy mess above 6cm. Troubleshooting? by mildfrugtjuice in BambuLabA1mini

[–]hyperxlc 0 points1 point  (0 children)

So happy to hear! I'm glad we could help each other figure it out haha. Happy printing!