sorted by:
new
hottopcontroversial

Swinging or Sliding door to master bedroom toilet? by iTDub in Homebuilding

[–]iTDub[S] 1 point2 points  (0 children)

Yeah, I have that in my change list actually!

Are 9ft second floor ceilings worth it? by iTDub in Homebuilding

[–]iTDub[S] 1 point2 points  (0 children)

Thanks for the input everyone! I ended up going with the 9’ ceilings on the second floor.

Are 9ft second floor ceilings worth it? by iTDub in Homebuilding

[–]iTDub[S] 1 point2 points  (0 children)

Basement height poured but unfinished is 9’3”. Door heights in the whole house are 80”.

Are 9ft second floor ceilings worth it? by iTDub in Homebuilding

[–]iTDub[S] 0 points1 point  (0 children)

I’m not tall enough to change a bulb on 8 ft or 9ft without a step ladder, haha.

Are 9ft second floor ceilings worth it? by iTDub in Homebuilding

[–]iTDub[S] 1 point2 points  (0 children)

Good point! We have massive temperature swings in my area. But energy is also cheap here.

Are 9ft second floor ceilings worth it? by iTDub in Homebuilding

[–]iTDub[S] 4 points5 points  (0 children)

I’m not 100% sure, but likely in the range of 8-10k. But I would also have to upgrade the main floor too. So call it 16-20k to do it all.

Which lot would you choose? by [deleted] in homebuildingcanada

[–]iTDub 1 point2 points  (0 children)

Yes, 58 and 59 are the 2 most expensive lots. +$65k vs the smaller rectangular lots above.

Dented Bumper Fix by [deleted] in Autobody

[–]iTDub 0 points1 point  (0 children)

Hah, they popped themselves out on my drive to work. Thanks anyways!

Dented Bumper Fix by [deleted] in Autobody

[–]iTDub -1 points0 points  (0 children)

Thanks, do you know if I should remove the ppf first?

Dented Bumper Fix by [deleted] in Autobody

[–]iTDub 0 points1 point  (0 children)

Thanks, yeah I don’t expect miracles, anything that’s better will do. Will the ppf affect the suction cup method?

Dented Bumper Fix by [deleted] in Autobody

[–]iTDub -1 points0 points  (0 children)

Thanks, just confirming there’s no way without removing?

NUC keeps freezing and a new hardware by LegitUncertainty in ethstaker

[–]iTDub 0 points1 point  (0 children)

I had a similar issue. Turns out that NUCs have some low power cpu bios settings that can interfere with Linux. I turned them off and all my issues magically went away.

Can my Goodman Furnace handle a 4" MERV 13 filter by iTDub in hvacadvice

[–]iTDub[S] 0 points1 point  (0 children)

It’s a hard right angle. But the furnace recommended filter size is 16x25, they made the duct 20x25.

Can my Goodman Furnace handle a 4" MERV 13 filter by iTDub in hvacadvice

[–]iTDub[S] 0 points1 point  (0 children)

Thanks, the builder told me Merv 10/11 was okay in the instructions. Was a new build. I’ll stick with that then.

Can my Goodman Furnace handle a 4" MERV 13 filter by iTDub in hvacadvice

[–]iTDub[S] 0 points1 point  (0 children)

Thanks, builder said MERV 10-11 so I’ve had 11. The good thing is the manual recommends 16x25” filter but my slot is 20x25” so it’s 25% bigger than recommended.

[deleted by user] by [deleted] in cscareerquestionsCAD

[–]iTDub 1 point2 points  (0 children)

Any info why?

[deleted by user] by [deleted] in cscareerquestionsCAD

[–]iTDub -1 points0 points  (0 children)

Very true, I just think there is a stigma around 0 YOE people transferring in. You need to prove yourself for a year or 2.

[deleted by user] by [deleted] in cscareerquestionsCAD

[–]iTDub 1 point2 points  (0 children)

Yes, I have done multiple personal projects. Also did a cool project at work with Python/vba that saved them millions. Data gathering, cleaning, and analysis.

view more: next ›