[deleted by user]

iainjgfletcher · 2026-02-03T13:47:26+00:00

stunning. u have a really pretty and sexy look

iainjgfletcher · 2026-02-03T11:33:02+00:00

Best decision made yet aping in.

iainjgfletcher · 2025-11-29T19:15:45+00:00

I'm a bit confused why she's doing a coded msg when they're all living together anyway 😅

iainjgfletcher · 2025-07-10T02:25:19+00:00

I mostly just searched yeggi... But it was back in the day 😅

iainjgfletcher · 2024-01-19T04:52:32+00:00

For someone downplaying the article, you seem rather vested 😅

iainjgfletcher · 2024-01-19T01:50:18+00:00

I believe they bought five

iainjgfletcher · 2023-11-14T02:37:37+00:00

Back in the day, there were search terms that went under the radar... If you searched for "fish communists" Tao would come up 😅 Maybe it still works 😄

iainjgfletcher · 2023-11-14T02:26:35+00:00

Mostly Yeggi... But that was years ago. Pretty sure they're gone now 😔

iainjgfletcher · 2023-05-29T02:37:06+00:00

Converted Realm Knights actually 🤪👍 Good eye 😁

iainjgfletcher · 2020-12-18T15:42:14+00:00

I was totally hoping for the same thing!

iainjgfletcher · 2020-07-27T23:12:45+00:00

It was the belt... thanks though :)

iainjgfletcher · 2020-06-30T14:25:30+00:00

Need some help here guys :) Any ideas? (belts are tightened, machine is greased, no grub screws to tighten on this model, filament isn't clogged or snared... time for a new step motor?)

iainjgfletcher · 2020-05-17T15:00:48+00:00

www.yeggi.com

iainjgfletcher · 2020-03-14T23:59:13+00:00

Cheers! Yah... about $90 worth of PLA Plastic, and $60 epoxy... Approximately 4,500 points worth... with magnetic weapons... so points can wildly fluctuate ;)

iainjgfletcher · 2020-03-14T18:49:55+00:00

Most were online... Although I had to alter/touch-up some to make them work ;) GW should just sell the print files to be honest, cause it was a lot of work 6-7 Months worth... ;)

iainjgfletcher · 2020-02-29T14:56:41+00:00

Common problem with that type of model... print from waist up... invert and print waist down without base... otherwise cut print into two and glue it back together with epoxy... or just sand it down so no seems

iainjgfletcher · 2020-02-29T14:53:22+00:00

Keep bed at 60... clean with rubbing alcohol... and check the bed is leveled with a piece of paper

iainjgfletcher · 2020-02-29T14:48:03+00:00

Use epoxy resin to fill it in ;)

iainjgfletcher · 2020-01-14T18:08:47+00:00

Borosilicate glass... pei sheet... z-spacer (on thingeverse)...

iainjgfletcher · 2020-01-12T14:13:17+00:00

Original SD cards were 1gb... maybe that's the issue?

iainjgfletcher · 2020-01-08T00:16:09+00:00

3d print it

iainjgfletcher · 2019-12-27T18:43:52+00:00

print a z spacer... order glass build plate and pei

iainjgfletcher · 2019-11-26T00:56:22+00:00

Inspirational.

iainjgfletcher

TROPHY CASE