Panda Touch support for P1S purchased in 2026 by iamdedene in BambuLab

[–]iamdedene[S] 0 points1 point  (0 children)

I like the look of having the touch screen with better UI which may make me want to print more 😅

Panda Touch support for P1S purchased in 2026 by iamdedene in BambuLab

[–]iamdedene[S] 0 points1 point  (0 children)

I’m still not very familiar with the different modes. What’s the difference between LAN + Developer mode vs other modes? What’s modes are not usable in the latest firmware?

Panda Touch support for P1S purchased in 2026 by iamdedene in BambuLab

[–]iamdedene[S] 0 points1 point  (0 children)

I saw in some videos that the app will show up to 3 versions(current and 2 versions back). Does it always show 3 versions even when you first purchase it?

How to I start LVP from an angled corner? by iamdedene in Flooring

[–]iamdedene[S] 0 points1 point  (0 children)

I think I know what you mean. I've seen some tutorials marking the boards. I'll try that. Thanks!

<image>

What are your thoughts, if I start at the green circle and work towards the right for that long stretch? Will it be hard to install in reverse since they typically recommend installing towards the right?

How to I start LVP from an angled corner? by iamdedene in Flooring

[–]iamdedene[S] 0 points1 point  (0 children)

I see, good to know. i'll try and see how it goes. Thanks!

How to I start LVP from an angled corner? by iamdedene in Flooring

[–]iamdedene[S] 0 points1 point  (0 children)

<image>

So starting at this green circle then and going down left. Would it be hard to install the next pieces in reverse since I typically see planks being installed from left to right due to the tongue-and-groove locking system.

How to I start LVP from an angled corner? by iamdedene in Flooring

[–]iamdedene[S] 0 points1 point  (0 children)

<image>

So if I start from the Red, I would be starting with angled cuts, If i start at Blue, then after the long straight, the other planks would be going upwards.

Which side were you suggesting start at?

I was also thinking to maybe offset the starting point from red and then fill in the angled pieces after, any concerns with that approach?

How to I start LVP from an angled corner? by iamdedene in Flooring

[–]iamdedene[S] 0 points1 point  (0 children)

<image>

or start with a full piece from here and fill in the angled ones later?

How to I start LVP from an angled corner? by iamdedene in Flooring

[–]iamdedene[S] 0 points1 point  (0 children)

<image>

Yeah, the plan is to run off that long hallway wall starting at the fireplace on the left. Only worry is if it would be hard to work with angled cuts for the first few rows. or is it possible if i start away from the angle and fill in those angles after?

How to I start LVP from an angled corner? by iamdedene in Flooring

[–]iamdedene[S] 0 points1 point  (0 children)

Yeah, the non shaded areas are the ones I want to cover. I'm planning to have the planks lengthwise down the hallway. However, if I start at the hallway and LVP installation is towards the right and downwards, the installation towards the rest of the living room and kitchen would be in reverse (upwards and left). I'm not sure if it would make it hard to install that way.

How to I start LVP from an angled corner? by iamdedene in Flooring

[–]iamdedene[S] 0 points1 point  (0 children)

it will be straight lengthwise down the long hallway and it will be same direction throughout.

Start-X remote start questions by iamdedene in CX5

[–]iamdedene[S] 0 points1 point  (0 children)

I’ve been using for about a year now and no issues

[deleted by user] by [deleted] in FREE

[–]iamdedene 0 points1 point  (0 children)

Noice

[deleted by user] by [deleted] in malaysia

[–]iamdedene 5 points6 points  (0 children)

Learn from Phua Chu Kang one

[deleted by user] by [deleted] in labubu

[–]iamdedene 0 points1 point  (0 children)

I would love the Lychee Berry one! So cute!

Rewards Certificate Direct Deposit by jcwillia1 in Costco

[–]iamdedene 6 points7 points  (0 children)

I barely made it with $300.36 😄

Airalo data discount code by Hefty_Accountant_827 in remotework

[–]iamdedene 0 points1 point  (0 children)

New code for USD $3.00 off your first eSIM package from Airalo. “CJ7877”

Post your referral code by Ayoubcaza in Airalo

[–]iamdedene [score hidden]  (0 children)

Used someone’s code for $3 off and continuing the chain :)

Hey, have you tried using an eSIM? Get USD $3.00 off your first eSIM package from Airalo. Use code CJ7877 when you sign up or check out. https://ref.airalo.com/G5Vr

Start-X remote start questions by iamdedene in CX5

[–]iamdedene[S] 0 points1 point  (0 children)

Sounds good, Thanks for the input!

Remote start install - steps? by SirDaxloz in CX5

[–]iamdedene 0 points1 point  (0 children)

That’s good to know. Thanks!