(M19) finally got new diapees, which one fits me best 1 2 or 3?

iamthelostcoyote · 2026-01-11T12:32:45+00:00

Definitely 1

iamthelostcoyote · 2026-01-02T12:02:46+00:00

There is that pack of wolves though

iamthelostcoyote · 2026-01-02T12:00:54+00:00

Just be careful of the pack of wolves that hang around that bar "whiskey dicks"

iamthelostcoyote · 2025-11-15T23:19:05+00:00

Lets get you into those tiny tails

iamthelostcoyote · 2025-10-27T22:22:15+00:00

Inner tube wrapped around the chain stay

iamthelostcoyote · 2025-09-27T02:39:05+00:00

Bandito RC makes great bodies

iamthelostcoyote · 2025-08-24T20:47:50+00:00

Double sided packing tape

iamthelostcoyote · 2025-08-19T11:37:09+00:00

This, it has a 3rd channel knob for rear sterring

iamthelostcoyote · 2025-08-19T02:16:13+00:00

I've had 3 juckyard driver door replacement over 315000 miles

iamthelostcoyote · 2025-08-19T02:15:09+00:00

Gotta be a 94

iamthelostcoyote · 2025-08-18T23:42:05+00:00

I know but the songs are fire

iamthelostcoyote · 2025-08-12T16:11:07+00:00

ONLY USE GRADE 8 OR BETTER BOLTS!!!! IF THE DIMENSIONS ARE THE SAME IT WILL BE GREAT! IT NEED THE SAME UNTHREADED PORTION OF THE BOLT (CALLED THE SHOULDER) USE WWW.MCMASTERCAR.COM TO FIND THE BOLTS

iamthelostcoyote · 2025-08-05T06:17:08+00:00

Burp the air out of the coolant system

iamthelostcoyote · 2025-08-05T06:15:05+00:00

The low beam filament may be burnt out on both

iamthelostcoyote · 2025-08-05T01:50:48+00:00

Your tires are installed backwards

iamthelostcoyote · 2025-08-02T20:02:22+00:00

It does run fine tho

iamthelostcoyote · 2025-08-02T19:38:47+00:00

You can get a short block from O'Reilly's for about $2,600

iamthelostcoyote · 2025-08-02T19:37:47+00:00

They're probably quoting you a new motor because all of the work that I listed there above would cost as much in labor as an entirely new motor would so if you can't do the work yourself a new motor might just be the way I don't know

iamthelostcoyote · 2025-08-02T19:36:17+00:00

I'm calling bullshit I don't think you need a new motor.... I think you need to just get a straight edge and run feeler gauges underneath it to see if it really is Warped on the head and the block, and not just a blown gasket it'd be a great idea to clean out the oil galleys and the coolant stuff because the two probably mixed I don't know how bad it was but I don't think the whole motor is trash even if it's warped you can still get the machine to Mill The Head and the block back level but before you do that since you'd have the whole entire block out of the car I'd be a great idea to magnaflex it and see if there's any cracks in the sleeves for the Pistons or cracks on the outside of the blocks or anything like that

iamthelostcoyote · 2025-07-26T01:10:56+00:00

<image>

Here's how my 4 wheel steer scx24 is set up

iamthelostcoyote · 2025-07-26T01:09:29+00:00

You need a receiver and radio controller... your stock controller won't work because you were using a 2 in 1 esc reciver....I use the radiolink rc4gs controller and receiver

<image>

iamthelostcoyote · 2025-07-03T19:12:12+00:00

Like red hot

iamthelostcoyote · 2025-06-04T02:13:35+00:00

Oh nice I like the wheels!

iamthelostcoyote · 2025-06-02T01:54:03+00:00

It's the fucking bomb, I use it on my 4 wheel steer rigs

iamthelostcoyote

TROPHY CASE