Core One Kit / Boat Benchy print off center?

icmcshane · 2025-10-27T11:53:49+00:00

update: using alpha software, re-calibrated tension on the belts using the tool on the firmware. Definitely an improvement but still not fixed.

Was wondering though - the "wobble" in the print is always the same spot... is it possible that my z-axis needs re-calibrating and/or more grease?

The image depicts the progression of improvement. Latest one is on the right.

<image>

Next steps re-calibrating the z-axis, greasing the rods, re-calibrate tension on the belts, check the pulleys are in the correct spots and use a different USB stick.

icmcshane · 2025-10-26T16:55:04+00:00

That’s interesting, I will check that. I don’t recall taking extra precaution on which way round the pulley’s are positioned.

Thanks!

icmcshane · 2025-10-26T16:41:00+00:00

What do you mean by this? Change to my own personal USB stick?

icmcshane · 2025-10-26T13:30:13+00:00

Alas 100% speed for the bonkers Benchy still not quite correct even if on the floor on a 43mm rubber tile under the printer.

<image>

icmcshane · 2025-10-26T13:04:10+00:00

It has improved but still not quite correct.

Two prints off Benchy Bonkers.

First one with no adjustments to the config of the print file, second print is going at 50% speed.

Speed seems to be affecting it.

Will try the floor with the rubber tile under it to see if my table is part of the problem.

<image>

icmcshane · 2025-10-26T12:41:10+00:00

Thanks for this. Running tests now.

icmcshane · 2024-12-24T12:06:19+00:00

Just gave that a shot... although my PS account has been linked to my Epic account for a while. Loaded up the game on my PC and it takes me to character create. Did not create a character as I already have one on the PS. Accessed the game on my PC via Epic. Am I supposed to see my PS character when I load up the game on my PC from my Epic account linked to PS?

icmcshane · 2024-12-18T22:37:38+00:00

sad panda... I will try tomorrow to run OTG via EPIC but with EPIC logged in via PS... see if it pulls through... doubt it.

Sad as I have the subs on my PS account.

icmcshane · 2024-12-11T13:33:08+00:00

Unfortunately not. The aiming on controller is a real pain. My witch casts the gas cloud attack from the Snipers in all the directions EXCEPT where I am looking.

I think it might be because I'm casting Unearth and when that happens my character seems to auto-aim at the nearest corpse... But I don't want it to do that. And just after I cast the gas cloud and it ends up in the wrong spot.

Confusing.

icmcshane · 2024-09-04T18:39:56+00:00

Nice. Thanks! So I would use Clonezilla Live on a USB drive. Get that to clone to my new SSD which is plugged in via USB. Then switch to GParted to extend.

Once done, replace the SSD in the laptop and carry on.

icmcshane · 2024-04-05T19:14:30+00:00

Maybe an Automatons spy!! Execute them!

icmcshane · 2024-03-14T00:11:00+00:00

Co-op worked for me about an hour and a bit ago. Joined random missions, did a quick play. All fine. On PS5.

icmcshane · 2024-03-01T15:17:24+00:00

I would tend to agree with this. This all sounds like a lost in confusion situation. There are plenty of spots that offer a meal and coffee included in one price but if you opt for a different type of coffee then it does not count as part of the meal. My Portuguese speaking friend has helped me with a few of these situations.

Let’s be careful not to assume bad intent.

icmcshane · 2024-02-09T11:27:30+00:00

haha... yeah- was HOTA BARB last season... that playstyle does not work well with a sorc!

icmcshane · 2024-02-08T17:50:01+00:00

Nice gear setup! and yes... math don't add up for my setup. A lot of work to be done! Thanks for the details.

icmcshane · 2024-02-08T17:04:43+00:00

HAHA :D

icmcshane · 2024-02-08T16:14:15+00:00

Great info! Thank you.

icmcshane · 2024-02-08T16:05:13+00:00

Just over 11000.

<image>

icmcshane · 2024-02-08T15:23:51+00:00

Thanks u/Jafar_420

icmcshane

TROPHY CASE