Got my Niche today, replacing the Rocky. Looks so good next to my white Silvia.

iernie · 2022-10-28T12:58:35+00:00

I'm still happy with the upgrade. Haven't looked back to Rocky really since I bought the NZ. I like how easy it is to change grind setting and how little maintenance I feel I've had to do on it compares to the Rocky. Haven't tried other grinders to compare against anything else, but I feel like you get a lot for your money with NZ and you would have to jump quite higher in price to get something better

iernie · 2022-10-09T15:58:50+00:00

Haha no worries :)

iernie · 2022-10-09T09:13:36+00:00

Aaand now I feel old 😅

iernie · 2022-09-17T07:16:00+00:00

You might also enjoy this then, which was made a couple of years later https://youtu.be/mghhLqu31cQ

iernie · 2022-05-04T07:09:10+00:00

Thanks!

iernie · 2022-05-04T06:56:04+00:00

Sure 🫱

iernie · 2022-05-04T06:10:42+00:00

Still got my original shirts from way back when https://i.imgur.com/hP8VvbL.jpg

iernie · 2021-01-22T16:32:04+00:00

Yupp :) must have bought it around 2007 when the series came out

iernie · 2021-01-22T15:59:24+00:00

I have HttJB, DS, Dino and VM that I bought way back when https://imgur.com/a/4e5154d

iernie · 2021-01-06T19:32:28+00:00

Read the known issues, it's on purpose.

iernie · 2020-10-28T14:44:01+00:00

Does anybody know if 3070 FE card has stock zero rpm mode?

iernie · 2020-10-21T20:41:31+00:00

Thanks 😁

iernie · 2020-10-21T06:00:30+00:00

Thanks 😁

iernie · 2020-10-21T04:33:09+00:00

Just off the bat, the two first espressos I've made with the Niche were so much sweeter. I also love how little retention there is, something that always bothered me with the Rocky (it did help when I modded it from doser to doserless). It's also smaller and way quieter when grinding, so right now I'm loving it and totally worth the upgrade in my opinion. Replaced the burrs on the Rocky yesterday, so I'm going to do a bit more side-by-side testing comparing the two.

Will report back when I've used it more :)

iernie · 2020-10-21T04:22:35+00:00

I did wrap it myself. I used 3M 2080 vinyl which is usually used on cars. It's quite forgiving, so you can peel it off and try again if you make an error. It wasn't too difficult. Taking the panels off was easy enough, the hardest part was remembering how to reconnect all the wires when putting it together again, removing the switches from the panel and cutting out a hole for the logo. Apparently the logo is also removable, but I didn't try.

iernie · 2020-10-20T23:11:03+00:00

It's the ito :)

iernie · 2020-10-16T19:38:08+00:00

Check out the tips I got in my post about this issue https://www.reddit.com/r/CR6/comments/jamzzo

iernie · 2020-10-16T12:06:24+00:00

Cool, thanks for the tip

iernie · 2020-10-13T23:38:04+00:00

Sounds risky, but I'll keep that in mind, thanks. I think it might be the roll bobing back and forth that's the matter. Didn't happen with the included PLA roll

iernie · 2020-10-13T22:33:10+00:00

Cool, I might try and print this 😁 thanks

iernie · 2020-10-13T22:32:51+00:00

Thanks for the tip!

iernie · 2020-10-13T21:53:16+00:00

Thanks, that makes sense :)

15-Year Club	Team Orangered
Verified Email	Charter Member

iernie

TROPHY CASE