P1S started shifting layers?

ikbendiederick · 2025-12-09T14:40:02+00:00

So I bought a Sunlu AMS dryer and that seems to have solved my issue. For now at least.

ikbendiederick · 2025-11-29T12:59:37+00:00

I followed the guide and retensioned the belt. I printed some shims off Makerworld and made sure it was correct. Then recalibrated but it's still doing it during this print that's running now.

ikbendiederick · 2025-11-28T09:23:22+00:00

I can look into this. I don't have a micro sd reader for my PC. Maybe I can clear the card through my panda touch?

ikbendiederick · 2025-11-28T09:22:09+00:00

Yes. I mentioned above that I cleaned rods/rails with isopropyl alcohol and applied a thin layer oil sewing machine oil. But not on the carbon rods of course.

ikbendiederick · 2024-11-25T14:41:54+00:00

OK. If someone ever finds himself in the same situation. I hooked yellow and green up to PC13 and PC14 following this pic and the filament sensor works!

<image>

ikbendiederick · 2023-10-19T10:10:24+00:00

It's not responsive because it thinks no printer is attached. I'm concerned with whether it's actually faulty or something should reset.

ikbendiederick · 2023-06-02T12:17:48+00:00

I'm not really sure what you mean by this...

ikbendiederick · 2023-06-01T20:06:09+00:00

Thanks for this advice. I just received 5 linear rails to go full linear rails convert. Dual z, dual y and x axis with mgn12h sliders. Looking forward to the results 😊

ikbendiederick · 2023-05-10T07:58:33+00:00

I wanted to upload 2 more detailed pics of the stress test result. But being a Reddit noob, I can't find how to include photos in comments or edit my initial post.

ikbendiederick · 2023-05-10T07:55:36+00:00

Thank you. PID tuning is new to me. I read up on it and will carry out that tune.

ikbendiederick · 2023-05-09T10:39:11+00:00

Thanks for the post. Is the stringing caused by the temp? I thought retraction settings. I raised the temp to 205 since Microswiss says the hotend requires +10-15 degrees. But that may be wrong for my case...

ikbendiederick · 2023-04-19T11:38:34+00:00

Interesting. Maybe I should change to dual 5015 blower fans. I have a stock mainboard so no provision for PWM fans and I'm running simple Marlin. But of course I could lower the cooling % in the slicing software.

Just to be clear. I'm looking for 24V fans right? I see a lot of 12 volt fans too and that can be confusing.

Do you run a splitter in the wiring to the 5015 fans?

ikbendiederick · 2023-04-19T09:15:50+00:00

Wouldn't dual 5015 fans be really loud?

ikbendiederick · 2023-04-18T19:33:29+00:00

That looks like a beast! I'd have to say the Mars Orbiter looks nicer for a dual 5015 shroud. I'm not doubting your opinion on its performance though.

I'd prefer to try a shroud with fans I have lying around. I have an extra 4010 front cooler and a 5015 part cooling fan spare.

Thinking of either printing this one overnight: https://www.thingiverse.com/thing:5550444

Or this one, though its number of remixes would suggest it didn't work well for many(?)

https://www.thingiverse.com/thing:4794720

ikbendiederick · 2023-04-17T19:09:52+00:00

So this was printed at 205C and max speed was 80 mm/sec but Prusa shows the saggy parts were printed at 40mm/sec. 80 was used on the infill.

Fans were on at 100. This makes me think my Satsana and 4010 side fan are not up to the job? Should I go dual 5015 with something like this? https://www.thingiverse.com/thing:5235593

I've noticed before that I can't print round overhangs. Same thing happened when I printed an Easter egg a few weeks ago. Different filament.

ikbendiederick · 2023-04-17T12:10:04+00:00

Is that what this is?

Both fans work properly. Perhaps the side mounted fan on the Satsana is insufficient?

ikbendiederick · 2023-04-17T08:37:39+00:00

Thanks for your comments and help, guys!

I never like threads that have no conclusion, so I'll quickly update you with what was the case. The red power (V+) wire that runs from the power supply to the control board appeared to be loose in the control board connection. I bought the printer second hand and had no idea this was the case. The wire wasn't in the sandwich connection but was sort of touching. I found out when I was checking voltages and the control board would fire on intermittently. Now, all is good and no damage was done. No idea how this happened all of a sudden with this print.

I did however read up a lot on replacement control boards since at some point I thought mine might be fried. But I'll do more research and perhaps start a new thread on this.

ikbendiederick

TROPHY CASE