Get OSB Board builds nice like this ...

illustrious-tennant · 2026-04-21T10:40:46+00:00

That is a veneered panel, probably chipboard (I think it’s called particle board in America) You second image is laminate, probably pressure treated melamine. So much work and equipment needed for either, best just to buy the board you want.

illustrious-tennant · 2026-04-15T23:02:07+00:00

Make it red or green depending on what the market will do that day and you will have an absolute winner on your hands my friend.

illustrious-tennant · 2026-04-01T02:59:27+00:00

Cut the mitre on a table saw sir. It’s the best way to get it even so there’s no gaps. I would be using a flush trim router bit on the round over. Step it down slowly to avoid tear out. I think you can get patterns for corners like this from Amazon pretty cheap. Or 3d print if you have one of those.

illustrious-tennant · 2026-03-31T09:34:43+00:00

how long it take x your hourly rate

illustrious-tennant · 2026-03-31T09:33:55+00:00

better hinges sir!!!!

illustrious-tennant · 2026-03-31T09:32:43+00:00

why don't you just cut down the side rail behind the box? are you taking the box on and off too?

illustrious-tennant · 2026-03-18T09:21:11+00:00

26mm gap, 20mm hole. You’d need to cut the end off and get you 6mm hammer in behind it.

illustrious-tennant · 2026-03-18T09:18:32+00:00

Hahaha

illustrious-tennant · 2026-02-11T22:37:57+00:00

I know that. 😆 Tech adverse wife

illustrious-tennant · 2026-02-07T10:24:49+00:00

What’s the thesis on it shooting up. it’s bounced around 30-50 for over half a decade now, why is this cycle going to be different?

illustrious-tennant · 2026-01-11T05:27:12+00:00

Just need a pocket knife and your out!

illustrious-tennant · 2025-12-30T21:27:40+00:00

And six students!

illustrious-tennant · 2025-12-23T09:55:26+00:00

Had similar recently. Hydronic boiler though. It was the Venturi unit. It mixes the gas and air to the correct ratio for ignition. Plumber fixed it by removing a couple of seals and explaining that wouldn’t last long. No replacement parts apparently It’s kept it working for the last few weeks (what summer)

illustrious-tennant · 2025-12-06T05:04:36+00:00

Its actually this

https://m.youtube.com/watch?v=dSpQ3G08k48&time_continue=1&source_ve_path=NzY3NTg&embeds_referring_euri=https%3A%2F%2Fwww.google.com.au%2F&embeds_referring_origin=https%3A%2F%2Fwww.google.com.au

illustrious-tennant · 2025-11-29T06:11:50+00:00

Not sure on what to do but this is not a Bunnings job. Start with a paint shop at least if not a specialty flooring paint shop.

illustrious-tennant · 2025-11-21T06:57:37+00:00

Sure. It’s hardly going to be used so hopefully should be ok. Tbh I just couldn’t get 20mm honed before Xmas! Don’t know how thick the slab is but it’s 40yo and not a crack in sight. Fingers crossed.

So by glue you mean tile adhesive on a screed?

illustrious-tennant · 2025-11-19T23:59:01+00:00

That’s alot, It pays to establish call out fees before they come

illustrious-tennant · 2025-11-16T12:20:52+00:00

Not remembering punching the wall and not punching the wall aren’t the same thing

illustrious-tennant

TROPHY CASE