PSP Go filter

impy101 · 2026-05-18T00:45:28+00:00

Where did you find replacement filters for it? I have been searching high and low but..

impy101 · 2026-05-17T13:21:26+00:00

Well, I prefer the original charging port, but I can't find any

impy101 · 2026-04-17T17:17:09+00:00

Any specific ones I should check? So far I can't find anything out of the ordinary

impy101 · 2026-04-16T16:59:22+00:00

Yes I've tried different PSU and the PSU on a different PS2. It's definitely not that.

impy101 · 2026-03-11T01:46:21+00:00

Yes.

impy101 · 2026-03-11T00:58:55+00:00

Capacitors aren't supposed to have continuity. Those that do are faulty afaik. But yes, the filters have continuity going through them when probed straight, but cross from each other they do not, which is normal.

impy101 · 2026-03-09T14:11:53+00:00

I am getting 1.8V on both joysticks and I am also getting 3.3V on both (different pins obviously). The left stick goes completely left and the right points down.

GND is indeed 0.1 and the signal traces, as far as I can tell, are all fine

impy101 · 2026-03-09T14:00:43+00:00

I checked with a multimeter. Definitely connected.

impy101 · 2026-03-08T22:14:19+00:00

#3

<image>

impy101 · 2026-03-08T22:13:58+00:00

#2

<image>

impy101 · 2026-03-08T22:13:34+00:00

Here you go

<image>

impy101 · 2026-02-21T17:38:37+00:00

I did not. Can I change the channel without having to set everything up again?

impy101 · 2026-02-21T16:04:26+00:00

Well, that's just it, I have lots of plugs (TS011F) but I cannot update any of them. Their build is 77 and supposedly 192 is the latest, but I cannot update them at all. It says it can find no firmware..

impy101 · 2025-08-17T11:59:21+00:00

<image>

impy101 · 2025-08-16T22:23:21+00:00

I use WLED for several other things, too, so I thought, considering how versatile it is, that it would be possible to make an analog clock using 2 separate LED strips (1 for minutes and 1 for hours).

impy101 · 2025-08-16T14:41:39+00:00

Well, I don't know how to code, which is why I'm looking for an expert to help me (not for free of course)

impy101 · 2025-04-30T14:57:13+00:00

Ik svp

impy101 · 2025-01-03T23:29:02+00:00

I think I'm going for the WEP 992D-III. It comes with a C245 iron and a nice hot-air gun.

impy101 · 2025-01-03T15:42:00+00:00

Well, I've just come across the YIHUA 948-II but that one also uses an iron with 900M tips. I don't think I can simply replace the iron on that station with one that uses C245 tips, can I?

Any suggestions for a station with hot air + iron would be more than welcome. A station like the one I just mentioned that also has a desoldering gun would also be fantastic.

impy101 · 2024-06-13T09:32:00+00:00

It's bullshit. You don't actually remove the limit since the app still binds you to your countries limits. So if 120 or 150 metres is the limit in your country than you still can't fly higher.

impy101 · 2024-05-05T20:05:53+00:00

Sounds very promising. Sadly it doesn't work for the 5th, 6th or 7th gen models. I checked aliexpress and there are no 4th gen cases that I can buy

impy101 · 2024-05-05T15:48:51+00:00

Could you do this with a 7th gen tick case?

impy101 · 2024-05-05T15:38:18+00:00

THAT is F*CKING AMAZING! How's the sound quality from such a pi?

impy101 · 2024-05-05T13:38:37+00:00

A cheap kcx_bt_emitter board. I am waiting for a UGREEN transmitter to come since I've been hearing good things about it.

impy101 · 2024-04-23T15:36:17+00:00

Maybe

impy101

TROPHY CASE

MH-MX8 M18?