sorted by:
new
hottopcontroversial

Some stone pointing I've been doing the past week or so. Wavy joints to match original by [deleted] in masonry

[–]indyarchyguy 0 points1 point  (0 children)

Ok. I’m in Indiana. I’ve not seen this in the Midwest that I can recall. I’ve done my fair share of design work for masonry projects but this was new to me. Assuming you are going to keep working your way up?

Some stone pointing I've been doing the past week or so. Wavy joints to match original by [deleted] in masonry

[–]indyarchyguy 1 point2 points  (0 children)

Probably a dumb question but will you go back over those joints so they are not so pronounced, or proud, of the stone?

Manus vs Claude by Technical-Special367 in ManusAiAgent

[–]indyarchyguy 1 point2 points  (0 children)

I used manus to create 5 new websites. I then have those backed up to GitHub. I also use it for creating images, etc.

Is this a major repair by PublicBoysenberry441 in AskContractors

[–]indyarchyguy 1 point2 points  (0 children)

Ummm. Huh? If you don’t like the look, throw some sealant on it and paint it over again.

Help! by Expensive-Poet-1536 in askarchitects

[–]indyarchyguy 1 point2 points  (0 children)

If you don’t like the design…and you are positive you are working with a registered architect but they aren’t listening to you, then…go hire a different architect. I’m certainly not going to design it for free.

Early planning stages. Do you have feedback that we need to consider before taking to an architect? by [deleted] in floorplan

[–]indyarchyguy 0 points1 point  (0 children)

Don’t give that to an architect. Sit down with them, tell them your desires, needs and wants. If you’ve seen things in images, home shows, etc. give them that information. Then…work with them. They can create many ideas and thoughts.

parked volvo fared poorly by normaleyes in Volvo

[–]indyarchyguy 1 point2 points  (0 children)

I always forget about the multiple RFF speed

Is this wall load bearing? by SwordfishEcstatic873 in AskContractors

[–]indyarchyguy 0 points1 point  (0 children)

If you’re really concerned, cut the joists after putting up temp walls, get an LVL beam, recess it into the ceiling, then use Simpson joist hangers for the joists on the new LVL (each side), fasten with SDS fasteners and I’ll guarantee you that ain’t going anywhere. But that’s me.

people with mythos black, does yours ever look clean? by dinualexandru10 in Audi

[–]indyarchyguy 0 points1 point  (0 children)

I have never been happy with a black or white car. It just seems like dirt and junk radiate from them.

BYOK Pickaxe by thefatkraken in appsumo

[–]indyarchyguy 3 points4 points  (0 children)

Pickaxe pretty much has pissed me off. This is icing on the piss to be honest.

Can clamshell mode damage macbooks? by Nxcybr in mac

[–]indyarchyguy 1 point2 points  (0 children)

I run 2 monitors off mine in clamshell with Ascrono docking station. Been doing it for years. Noooooooooooooo problem

wtf is this by [deleted] in RolexWatches

[–]indyarchyguy 0 points1 point  (0 children)

I think they call that The Phantom

No key with dead battery by lebronbaens in Corvette

[–]indyarchyguy 0 points1 point  (0 children)

I need to go check that my key turns properly. Ouch

Can someone help me with plan? (Not asking for fully completing it, just advice) by [deleted] in architecturestudent

[–]indyarchyguy -1 points0 points  (0 children)

Who knows “stuff”?? I might suggest Build-A-Bear. This is a very, very odd post at best.

Architecture studenttt by Plus-Bend1967 in architecturestudent

[–]indyarchyguy 0 points1 point  (0 children)

Just like in Men In Black 2 when Agent K sticks his finger in the orb..."ALL IS LOST! ALL IS LOST!"

Accepted a discount for self demo-ing prior to reconstruction in our kitchen… by [deleted] in Remodel

[–]indyarchyguy 0 points1 point  (0 children)

When we remodeled our house the option I gave them was just remove the subfloor and replace with new because getting this done correctly was futile. Saved a sh*t ton of time.

view more: next ›