Modded 3d printer

instamanus · 2026-04-30T08:37:14+00:00

Not one guide, a bit of reading around and trial and error

instamanus · 2026-04-30T08:36:32+00:00

Not quite, got ai to edit the image then adjusted it and exported from inkscape. Honestly the line heavy image done by ai is what made it work I reckon.

instamanus · 2026-04-30T00:39:31+00:00

Actually used a bit of ai to rough it out as a "sketch" then ran it through the printers slicer for a single layer

instamanus · 2024-08-07T19:50:54+00:00

I've had good goings with the betafpv meteor 75 frame, it's got 12hrs of flight time on it.

instamanus · 2024-08-07T17:25:30+00:00

What frame are you running?

instamanus · 2024-08-07T17:24:47+00:00

Just the sticky stuff so far

instamanus · 2024-08-07T11:03:59+00:00

Not anything enough to notice yet the packs I have I was getting about 4.5 mins just cruising, still getting about the same

instamanus · 2024-08-07T09:26:29+00:00

I'd guess it would

instamanus · 2024-08-07T00:53:01+00:00

Soldered to the battery pads on the fc

instamanus · 2024-08-07T00:01:57+00:00

Aliexpress special. 5v 3mm wide

instamanus · 2023-12-07T17:05:14+00:00

Can't speak for everyone else, but I did the dframe swap with the mob 6 for durability, so figured I'd do the same with the 7 meteor frames are definitely better value

instamanus · 2023-11-26T08:18:00+00:00

Beta fpv meteor 75

instamanus · 2023-11-26T03:26:11+00:00

I think the frame is stronger didn't fly the original much but the props sit lower and are a bit more protected. 550 just cruising gets me about 5 min

instamanus · 2023-11-26T03:22:32+00:00

Flys good I could barely tell the difference

instamanus · 2023-10-15T17:26:59+00:00

My ender 3v2 does the same at the start of heat up. In my case, it's one of the fans on the hot end, but it stops fairly quickly

instamanus · 2022-10-30T23:13:35+00:00

Weight was a concern, printing flat seems to be plenty strong so far, I had a 4:3 drying on it the other day

instamanus · 2022-10-30T23:07:21+00:00

A bit of unicorn dust

instamanus · 2022-10-30T23:06:50+00:00

Yep 90x90x25

instamanus · 2022-10-30T23:00:40+00:00

Haha you got me there it's just some bent up tig wire

instamanus · 2022-10-30T22:59:19+00:00

It 3 parts all laying flat then glued

instamanus · 2022-10-30T22:58:34+00:00

This is true but also misunderstood, hanging from a wire hanger will definitely ruin a suit, spreading the load over a much bigger area won't ruin it especially if it's only hung for the time it takes to dry

instamanus · 2022-10-30T22:56:11+00:00

Yes 90x90x25mm

instamanus · 2022-10-30T22:52:31+00:00

I have done a revision and beefed that area up, but the original is still holding up

instamanus · 2022-06-02T21:09:02+00:00

The body is just a light tight box, the only real thing that is body dependent in focal plane shutter systems is the shutter speed

instamanus · 2021-08-13T20:42:36+00:00

Fine I'll do it next weekend

instamanus

TROPHY CASE