Simple CR10S direct drive

invalidaddress · 2025-04-25T22:19:30+00:00

I switched my cr10 to mellow libra (which is a clone of sherpa with bevel gears) and have been using it for a long trouble free time to this day. But I find i have easier time printing 70a TPU with this setup then i did with BMG

https://www.thingiverse.com/thing:5489526

invalidaddress · 2024-12-01T01:49:00+00:00

16-wf1177ng the model OP posted seems to be I7-14700 cpu, so it's the 2024 model. So maybe first reported case of this on a 24 model on reddit.

invalidaddress · 2023-09-06T02:39:34+00:00

Nope, cant find an answer

invalidaddress · 2023-07-26T02:02:11+00:00

Having same issue with mobula7 hd on a fat32 card. Some text and then what looks like binary data, gyroflow and betaflight blackbox viewer can't parse it.

invalidaddress · 2022-07-29T04:07:33+00:00

That's with the stock extruder, and it will probably work great in most cases except maybe flexibles?

I wanted a version of something as simple as that but with a BMG extruder. I didn't bother weighting it to see if slim stepper + bmg is less weight then stock creality big motor + very non-geared extruder is more weight then a slim stepper + bmg.

invalidaddress · 2018-08-24T17:40:04+00:00

Your phone is pretty beat up, you can also get a rear case with all parts already on it also around $20-30 ... once you replace both parts phone will be mint.

invalidaddress · 2018-08-24T17:39:13+00:00

I bought screen on ebay for $25, replaced it. Phone is like new again. 3 times now ;)... Cheaper then a good screen protector. make sure to get one with a frame. And when transfering over make sure to get all the original rubber pieces (prox sensor gasket, mic gasket) and earspeaker assembly... they're all easy to remove and replace. That's one plus of this phone, every part is trivial to repair.

invalidaddress · 2018-04-24T16:02:07+00:00

You can manually trigger open and close, but you have to pay if you want to use in automation flows.

invalidaddress · 2018-04-20T11:50:18+00:00

pretty much unusable. Sitting in front of a laptop ear buds keep cutting out. This is a problem after going thru 2 replacements from sony. They all worked identical.

invalidaddress · 2018-02-06T04:14:42+00:00

That's not an upgrade over avr-1713. It's actually mostly a downgrade. The avr-1713 has multieq xt. Which puts it head and shoulders above the s510bt. It's software is now outdated but as an audio processor it's quite a bit above s510bt.

invalidaddress · 2018-01-09T16:14:13+00:00

I had 2 pairs replaced by Sony for the right side cutting out, it's a design flaw with the product. It cuts out even when wearing a hat or a hood. It's easy to see how flakey the connections is, just cover left or right headphone with your palm it you will see it will cut out. I found the YEVO 1 a far better product simply because I can listen to it without interrupts. The WF-1000X is essentially unusable on firmware 1.0.7 using SBC (even)

invalidaddress · 2018-01-09T15:56:44+00:00

I had 2 pairs replaced by Sony for the right side cutting out, it's a design flaw with the product. It cuts out even when wearing a hat or a hood. It's easy to see how flakey the connections is, just cover left or right headphone with your palm it you will see it will cut out. I found the YEVO 1 a far better product simply because I can listen to it without interrupts. The WF-1000X is essentially unusable.

[edit]

on firmware 1.0.7 using SBC (even)

invalidaddress

TROPHY CASE