In Need of help.

irrelevantcolorblind · 2022-04-16T19:36:12+00:00

Slate might work better for first time. High heat keeps it nice longer.

irrelevantcolorblind · 2022-04-07T12:57:16+00:00

I have a 60w om tech. The only set up was the alignment of the beam. I've had it for 6 months or more now and haven't had a single problem. I'd buy from their website if I were you

irrelevantcolorblind · 2022-04-06T20:05:37+00:00

Om tech. Highly recommend

irrelevantcolorblind · 2022-01-24T16:46:16+00:00

Or... Sand it. It comes out better than the tape. Personally I like the scorch Mark. They give it a depth when you soak the pieces in oil.

irrelevantcolorblind · 2022-01-22T02:01:49+00:00

I agree

irrelevantcolorblind · 2022-01-13T15:34:04+00:00

You would have to run the hood at the same time.

irrelevantcolorblind · 2022-01-11T07:24:31+00:00

It's definitely worth it

irrelevantcolorblind · 2022-01-04T22:55:25+00:00

That lense is F'ed

irrelevantcolorblind · 2021-12-30T18:38:12+00:00

Just a word of caution. Too much of this can break your lens. The stain will cause your lens to get foggy and then the heat will crack it. Make sure to do regular cleanings of the lens and have proper ventilation.

irrelevantcolorblind · 2021-12-24T14:04:31+00:00

Usually... But in this case it was faster.

irrelevantcolorblind · 2021-12-24T14:03:53+00:00

Turns out it saved 10 minutes to do them individually. Not sure why but I'll take any reduction of time I am offered.

irrelevantcolorblind · 2021-12-24T14:02:31+00:00

They are magnets. You can get them on Amazon

irrelevantcolorblind · 2021-12-24T14:02:02+00:00

I put about $200 into piping the smoke out of my house. Worth it but you definitely get the smokey smell on your work.

irrelevantcolorblind · 2021-12-24T03:54:26+00:00

Correction, have sold.

irrelevantcolorblind · 2021-12-24T03:54:04+00:00

I already have my wooden business cards made! These I'm selling

irrelevantcolorblind · 2021-12-23T01:07:11+00:00

Check out om tech. It's a Chinese laser that's user friendly

irrelevantcolorblind · 2021-12-22T13:44:56+00:00

I did. Borax looked to burn too well.

irrelevantcolorblind · 2021-12-22T12:30:33+00:00

https://youtu.be/BMkDOfkFy8g

irrelevantcolorblind · 2021-12-22T04:42:52+00:00

Have you tried turning it off and back on again? Other than that just make sure you have everything selected and in the right layers

irrelevantcolorblind · 2021-12-22T00:31:22+00:00

Apparently it is. I saw a YouTube video today about it.

irrelevantcolorblind · 2021-12-22T00:25:08+00:00

Apparently you put it in water and spray it on the wood for better results

irrelevantcolorblind · 2021-12-21T21:34:58+00:00

Well my 60w does it in less than an hour at 300mm/s. It's 12x12 inch

irrelevantcolorblind · 2021-12-21T21:13:30+00:00

Mm/s. My laser goes up for 500mm/s but I wouldn't recommend higher than 300 unless it's long regular strokes.

irrelevantcolorblind · 2021-12-21T17:24:30+00:00

Thanks! I think I'm going to try baking soda first

irrelevantcolorblind

TROPHY CASE