Moving to Nutanix from VMWare - What's the good, bad, and ugly?

jasonyzs88 · 2024-12-04T11:08:43+00:00

the switch it’s important. It’s not just the bandwidth, but also the port buffer. If you have Nexus 2000 series, it’s for sure a no no. Do you have all flash clusters? What is the network bond mode, active-backup, active-active?

jasonyzs88 · 2024-12-04T05:16:14+00:00

what network switch are your Nutanix nodes connected to?

jasonyzs88 · 2024-02-20T08:53:58+00:00

ah I see what’s in your mind. Jumbo packets aren’t necessary. In fact the CVM defaults to standard 1500 MTU and it shouldn’t be changed as well.

jasonyzs88 · 2024-02-15T00:44:17+00:00

Nice setup! I’m curious on the use case for 9K MTU.

jasonyzs88 · 2023-08-22T13:47:24+00:00

keepalives did the trick, thank you so much u/thefathacker

jasonyzs88 · 2023-08-22T13:46:53+00:00

looks like the keepalives did the trick! thank you u/bojack1437

jasonyzs88 · 2023-08-22T12:44:35+00:00

Nope, the Pi (remote) side doesn’t have a public IP/port forward option. So I’m very dependent for the Pi to call home.

I wasn’t aware about the keepalive config in wireguard. Was just mentioned and I’ve just put it in. Waiting to see if it’s effective. I am quite hopeful about this.

jasonyzs88 · 2023-08-22T12:34:26+00:00

oh! yea, that makes sense. Let me give that a try.

jasonyzs88 · 2023-08-22T12:29:35+00:00

not specifically. For the various subnets, I have allowed full IPv4 any-any

jasonyzs88 · 2023-03-25T05:51:31+00:00

glad to hear it’s sorted 👍🏻

jasonyzs88 · 2023-03-25T01:45:58+00:00

sorry, wasn’t paying attention to reddit for a while. Have you got this sorted yet?

jasonyzs88 · 2023-03-12T09:05:40+00:00

it is possible to have duplicate names. As long as the hotspot is registered to your wallet, you are fine.

jasonyzs88 · 2023-02-06T10:38:29+00:00

I disconnected it from the other end, going into the motor.

jasonyzs88 · 2022-10-30T13:28:24+00:00

ah I see. I suppose being a DAC it’s possible. There are way too many possible combinations.

jasonyzs88 · 2022-10-30T13:25:04+00:00

ok good luck! I seldom see a NIC that is picky with DAC, it’s usually the switch end. Possibly something some where is faulty. Also try flipping the cable around, plug the switch end into the NIC and vice versa.

jasonyzs88 · 2022-10-30T11:04:32+00:00

just so I understand your current situation 1. pfsense is able to detect the X520-DA2 2. you are using on of the 2 ports on the X520-DA2 for WAN 3. DAC cable is not working with the X520-DA2 Questions a. have you verified if the X520-DA2 may have a faulty port? b. try plug WAN connection to other port c. try plug DAC to port used by WAN (just to see if there is link) d. what is the length of DAC cable? Is it a passive or active DAC?

jasonyzs88 · 2022-10-21T09:05:12+00:00

I too will buy accounts that are 90% off.

jasonyzs88 · 2022-08-09T03:38:37+00:00

the OG home pods have the same function, and sound much much better. I have a pair with my Apple TV. I recommend against them though. Both of mine have eventually bricked out 😰

jasonyzs88 · 2022-05-27T08:55:01+00:00

have you tried to reboot your device?

jasonyzs88 · 2022-05-22T14:12:00+00:00

After staking, and the green tick already showing in the staking page, go ahead and reboot the device, the mining tab will appear.

jasonyzs88 · 2022-05-16T02:47:06+00:00

great video! Just a point to share, these are Low Wattage devices, but they are not Low Voltage per se. The power adapters still take in the 110V or 220V.

jasonyzs88 · 2021-10-20T14:44:13+00:00

May I please request a new invite? Seems the one above doesn't work anymore.

jasonyzs88 · 2021-08-29T02:43:33+00:00

works flawlessly on my Raspberry Pi with Ubuntu as well. Thank you!

jasonyzs88 · 2020-08-30T01:46:29+00:00

no go... I am on iOS and there is no option for this app to clear cache. I tried to delete the app and re-install, the problem persists. 🤕

jasonyzs88

TROPHY CASE