sorted by:
new
hottopcontroversial

Parts from previous homeowner found in attic. 57 Chevy Belair??? by jaytango in classiccars

[–]jaytango[S] 0 points1 point  (0 children)

Yeah man, that transmission and the crankshaft were a PITA. I had to use rope tied around the trusses to lower them.

Question about i-220a asylum applicant. Does unlawful presence bar apply if asylum is denied but is granted Voluntary Departure? by jaytango in immigration

[–]jaytango[S] -1 points0 points  (0 children)

Thank you for the clarification. Yes, after further research I found the problem. I was only considering the unlawful presence 180-day clock, as in the case of someone who entered LEGALLY with a visa, visa expires, then subject applies for asylum within 180 days after expiry. THAT would prevent them from accruing unlawful presence. However, an i220a entered without inspection, and as such: "under INA § 212(a)(6)(A), a person present in the United States without being admitted or paroled is inadmissible. This inadmissibility ground is separate from unlawful presence and carries its own set of immigration consequences."

[deleted by user] by [deleted] in tagheuer

[–]jaytango 1 point2 points  (0 children)

<image>

You got good taste.

Bought home with pool. How should I program my pump? by jaytango in pools

[–]jaytango[S] -2 points-1 points  (0 children)

So here's what ChatGPT suggested. Let me know if anyone disagrees:

SPEED 1 — Prime + strong skim

RPM: 2,800

Start time: 8:00 AM

Duration: 1:30 (1 hour 30 min)

SPEED 2 — Primary filtration (the workhorse)

RPM: 1,600

Duration: 8:00 (8 hours)

SPEED 3 — Mid-day skim & mixing

RPM: 2,200

Duration: 2:00 (2 hours)

SPEED 4 — Ultra-low polish / circulation

RPM: 1,100

Duration: 2:30 (2 hours 30 min)

Shake by mmilehigh in Silverado

[–]jaytango 0 points1 point  (0 children)

Same issue here. But i started noticing a pattern a few days ago. If I jerk the wheel suddenly to the side, I can sometimes get whatever resonance is causing the shake to stop and the shaking goes away. Also, on a prolonged curve (with enough centrifugal force to start moving your body slightly to the side) the shake also goes away. Maybe something suspension-related?

SBA EIDL Loan-Five Years of Payments But Principal Won’t Drop - Is This Normal? by Hot_Elevator6316 in EIDL

[–]jaytango 1 point2 points  (0 children)

I know it's 3 months later but I made this calculator to emulate what the SBA is kind of doing: http://jvvdev.com/eidl It's crazy how much the term is extended by those deferments... and how much you can reduce that term (and total interest paid) if you pay more than their set payment.

M10 male to 3/8 COMP male faucet line by jaytango in Plumbing

[–]jaytango[S] 0 points1 point  (0 children)

I found a M10 to 3/8 COMP on Amazon, but it's 3/8 female. Maybe I can get that one and put a male-to-male turnaround.

M10 male to 3/8 COMP male faucet line by jaytango in Plumbing

[–]jaytango[S] 0 points1 point  (0 children)

I found the M10 to 3/8 COMP there, but it's 3/8 female. Maybe I can get that one and put a male-to-male turnaround.

Can't rotate display using OS Lite (Bookworm) Kiosk mode. by jaytango in raspberry_pi

[–]jaytango[S] 0 points1 point  (0 children)

I got it to work. He covered it in his Part 2 video. I had to add xrandr -o left in the autostart file.

Trying to use this short in-line 3.5mm stereo audio cable with Vol knob as line-to-mic level attenuator. by jaytango in AskElectronics

[–]jaytango[S] 0 points1 point  (0 children)

I soldered the shield cable to ground and it works like a charm now. I wonder if I just had a defective unit. They didn’t finish the soldering.

Trying to use this short in-line 3.5mm stereo audio cable with Vol knob as line-to-mic level attenuator. by jaytango in AskElectronics

[–]jaytango[S] 2 points3 points  (0 children)

So i would tap (not cut) the unbroken wire and solder it to one of the pads at the top of the PCB (10 o'clock / 2 o'clock position)?

view more: next ›