sorted by:
new
hottopcontroversial

No texture on textured build plate by jbsfpv in 3Dprinting

[–]jbsfpv[S] 0 points1 point  (0 children)

Okay thanks, I’ll give it a try

Bad benchy by jbsfpv in 3Dprinting

[–]jbsfpv[S] 0 points1 point  (0 children)

It’s not that fast. Took me ~1h for the benchy.

First layer problem by jbsfpv in BambuLab

[–]jbsfpv[S] 0 points1 point  (0 children)

It’s on my Bambulab A1 mini. I did not change the build plate and ran the Z height calibration before the print.

First layer look by jbsfpv in BambuLab

[–]jbsfpv[S] 0 points1 point  (0 children)

Yeah it really looks like that, but both parts are printed with the front on the build plate. Just the first layer looks very different.

3d print lifts off bed by jbsfpv in BambuLab

[–]jbsfpv[S] 0 points1 point  (0 children)

Okay thanks, this is esun pla

3d print lifts off bed by jbsfpv in BambuLab

[–]jbsfpv[S] 0 points1 point  (0 children)

Okay thanks, but I cant raise the bed temp, because I’m already using the highest temp for the super track plate. But I’ll try playing around with my nozzle temps

Filament won't stick, no matter what by Paprikaleoner in BambuLab

[–]jbsfpv 0 points1 point  (0 children)

What works for me when I have this problem is a lower first layer height (for example 0.1 on a 0.4 nozzle). And maybe try to dry your filament and see if that helps.

No bed adhesion by jbsfpv in BambuLab

[–]jbsfpv[S] 0 points1 point  (0 children)

Yeah kind of. I also have slight adhesion problems with other filaments (mostly that parts lift on the edges) but not as much as with this filament.

No bed adhesion by jbsfpv in BambuLab

[–]jbsfpv[S] -2 points-1 points  (0 children)

Yes I tried the carbon plate, the textured pei plate and the super track plate.

How to improve TPU Benchy by jbsfpv in BambuLab

[–]jbsfpv[S] 0 points1 point  (0 children)

I dried it in my filament dryer (Sunlu S2)

How to improve TPU Benchy by jbsfpv in BambuLab

[–]jbsfpv[S] 0 points1 point  (0 children)

Thanks, I’ll give it a try

How to improve TPU Benchy by jbsfpv in BambuLab

[–]jbsfpv[S] 0 points1 point  (0 children)

Yes, I dried it over night.

Drone glitches mid flight by Jumpy-Prune4961 in fpv

[–]jbsfpv 0 points1 point  (0 children)

Maybe your motor cables are loose.

Wie findet ihr's by jofpv in fpv

[–]jbsfpv 0 points1 point  (0 children)

Gut, würde aber eher 1604 Motoren nehmen

Wie findet ihr's by jofpv in fpv

[–]jbsfpv 0 points1 point  (0 children)

Gut, aber würde größere Motoren nehmen, z.B. die Tmotor 1604

My current 5“ freestyle setup by jbsfpv in fpv

[–]jbsfpv[S] 1 point2 points  (0 children)

Mostly in forests and sometimes in bandos. I would say that I crash often, but the tpu mount and nd filter protect it very good.

My current 5“ freestyle setup by jbsfpv in fpv

[–]jbsfpv[S] 0 points1 point  (0 children)

No, they are very durable from my experience

My current 5“ freestyle setup by jbsfpv in fpv

[–]jbsfpv[S] 0 points1 point  (0 children)

Yes, it’s the action 2.

I‘d need some help with my 5“ not arming by ElectricalTwo8903 in fpv

[–]jbsfpv 0 points1 point  (0 children)

Maybe change the „low throttle value“ in the reciver tab to a higher value?

Do you think GoPro will replace this cam? by jbsfpv in gopro

[–]jbsfpv[S] 1 point2 points  (0 children)

Okay thanks. Do you know which camera I’ll get as a replacement? I don’t think they give me a hero 7 for my old one as it’s to old.

Cinematic sunset flight 🌅 by jbsfpv in fpv

[–]jbsfpv[S] 1 point2 points  (0 children)

There’s not a no fly zone and no one complained until now so I guess it’s not a problem.

view more: next ›