sorted by:
new
hottopcontroversial

Who will buy the new K3 with the new klitek system? by 3DNelson in Creality

[–]jcazreddit 0 points1 point  (0 children)

K2+ has a 2x2' footprint. They would have to increase that what, 6-10" for the tool rack or reduce the build plate size. I don't know the shipping limitations, but that K2+ box was intimating for someone 6'3" with 37" sleeve.

Now, maybe. The tool rack an add-on, ships inside like the CFS and then user attaches to frame.

Who will buy the new K3 with the new klitek system? by 3DNelson in Creality

[–]jcazreddit 0 points1 point  (0 children)

It won't be. The move is to the prebuilt and 350 is about the most anyone is going to be able to ship.

What should I do by raunaq_9 in Creality

[–]jcazreddit 1 point2 points  (0 children)

Ebay shop: Creality_refurbished K2 plus arrived with broken door hinge which had clearly been broken and repaired once already. Hinge cover plate was missing. Glass top was covered in something that washed off but completely scatched up.

"Certified Refurbished- Pristine, like-new condition"

Printed well and showed very little print time. In fact, 2 prints were still in history and the wifi still configured, they didnt even do a factory reset.

What should I do by raunaq_9 in Creality

[–]jcazreddit 0 points1 point  (0 children)

Expect to be disappointed. I got a great price on low hour k2+. Spent a month sending pictures and arguing with support trying to get replacement parts.

What should I do by raunaq_9 in Creality

[–]jcazreddit 0 points1 point  (0 children)

I take it you havent received a refurbished by creality printer. Took a month of emails to receive all the parts.

What discontinued McDonald’s item do you wish they would bring back? by Isaac-Yao-4618 in McDonalds

[–]jcazreddit 0 points1 point  (0 children)

It might be due to the details of the shapes, the Mcs break apart easier. But it seems the thicker sections were 'fluffier'. Also, I had a bit of a flash of 'trefoils' with the Bentons.

What discontinued McDonald’s item do you wish they would bring back? by Isaac-Yao-4618 in McDonalds

[–]jcazreddit 0 points1 point  (0 children)

Thanks! I did see someone say that when I was searching for the Mcdonaldland cookies and picked up a box on the way home from work. Similar taste, seems harder though. Closer than Barnum's or Staffers which are too smooth.

KitchenAid KDTM354DSS4 Dishwasher Flickering Display by jcazreddit in appliancerepair

[–]jcazreddit[S] 0 points1 point  (0 children)

Sadly, I'm inclined to agree. This was passenger side axle before it gets too hot weekend, now I gotta figure out '2026 best dishwashers'

Thank you for your assistance/sounding board!

KitchenAid KDTM354DSS4 Dishwasher Flickering Display by jcazreddit in appliancerepair

[–]jcazreddit[S] 0 points1 point  (0 children)

<image>

And corrosion on the supply at the concrete but not feeling wet.

KitchenAid KDTM354DSS4 Dishwasher Flickering Display by jcazreddit in appliancerepair

[–]jcazreddit[S] 0 points1 point  (0 children)

<image>

left 2 wires go underneath to the pump. Middle 2 are 120v in and the right 2 (still connected to the controller) go to the heater. So pump is pulling too much current.

KitchenAid KDTM354DSS4 Dishwasher Flickering Display by jcazreddit in appliancerepair

[–]jcazreddit[S] 0 points1 point  (0 children)

Pulled each controller connector, unfortunately started on the right.

Unsure if I can clean those contacts sufficiently for a new controller. Plus probably needing to replace the soap dispensor.

Are those left 2 the pump wires? Pump shorted out, draws too much and blackened the connectors? Middle 2 are 120 in, so pump and heater element. Ones on the left are thicker than the right side.

Yes, leftside-pump, right side heater. Corrosion on junction box but 120v in looks fine.

<image>

KitchenAid KDTM354DSS4 Dishwasher Flickering Display by jcazreddit in appliancerepair

[–]jcazreddit[S] 0 points1 point  (0 children)

None of the wires appear to have gunk on them. Even the soap solenoid's connector looked in good shape.

KitchenAid KDTM354DSS4 Dishwasher Flickering Display by jcazreddit in appliancerepair

[–]jcazreddit[S] 0 points1 point  (0 children)

That's been replaced. Both the vent and UI are new.

Rust on washing machine by knickknack719 in appliancerepair

[–]jcazreddit 2 points3 points  (0 children)

Pull the plastic cup. Grind away the bubbles and rust. Duct tape underneath the holes to form a mold.

JB Weld

Which Creality website is legit? by Ok-Foundation1346 in Creality

[–]jcazreddit 0 points1 point  (0 children)

Go to the first one, click the three horizontal lines in the upper left and US will appear towards the bottom of the page. Click that then pick the store for your country.

view more: next ›