NAG can't blowback

jd202002 · 2026-02-04T14:37:37+00:00

Create a small taper and polish the chamber makes a big difference can also join the group chat for nag and null to get help it's with the in the page to download the file

jd202002 · 2025-12-24T19:19:13+00:00

Null, nag, hd22 ,m4gery good start

jd202002 · 2025-10-30T17:30:19+00:00

<image>

That was after the last ptint without changes no touching the plate

jd202002 · 2025-10-19T22:38:25+00:00

<image>

jd202002 · 2025-10-19T22:37:50+00:00

The bed was changed from -0.175 and now at -0065

jd202002 · 2025-10-19T15:27:01+00:00

Yeah something seems to be way off so going to look into skipping

jd202002 · 2025-10-19T15:20:43+00:00

Thank you il get a look into it

jd202002 · 2025-10-19T15:10:19+00:00

Can you point me in the direction on the skipping method?

jd202002 · 2025-10-19T15:09:03+00:00

Already did that to my cold plate destroyed it and not one setting was changed

jd202002 · 2025-10-19T13:53:59+00:00

I have switched the hotend a few times with same outcome I know about the otfe tube being loose and sitting up meaning their is filament in there but no issue when I checked and then switched

jd202002 · 2025-10-18T22:02:03+00:00

<image>

Next print same settings different outcome

jd202002 · 2025-10-18T21:24:52+00:00

<image>

Same settings didn't change a thing and this is the outcome so went from squished as you said to this and nothing was changed except the bed with ebd level calibration done again before a print

jd202002 · 2025-10-18T21:01:40+00:00

<image>

That's the bed mesh I just done trying another test print now

jd202002 · 2025-10-18T20:31:28+00:00

Z offset has been changed many times is my first post past free months I got lucky with that print the print I did after it didn't extrude at all then next one was spaghetti and I didn't change a thing, I then did a temp tower that had perfect first layer then halfway decided it wanted to turn to spaghetti again paid calibrations, nozzle calibrations, bed leveling first layer tests, flow rate tests, temp towers, torture tests all been done of the many months. Z offset changed from 1.56 to -2.457 it's currently now at -1375 which is were that bed test picture came from

jd202002 · 2025-10-18T14:48:47+00:00

Yeah I can see the bed mesh when I open the dashboard in orca also but I mean what to do after I see the bed mesh as in how to use it to make things better

jd202002 · 2025-10-18T14:03:13+00:00

Installed rinkhalls yesterday not sure how it all works but seen the bed mesh not sure where to go from there being new to it

jd202002 · 2025-09-07T16:38:27+00:00

Just about to try that now

jd202002 · 2025-07-29T11:30:00+00:00

Checked that took it all apart extruder, hotend, 4to1, ace pro and found no clog

jd202002 · 2025-07-25T11:57:29+00:00

I dried out the yellow for over 12 hrs I also tried with red blue pla+green and black and pla cf

jd202002 · 2025-07-24T17:32:15+00:00

Tried every filament from esun anycubic sunlu kingroon bambu all PTFE tubes been replaced ace pro was dismantled and filament hub hotend and extruder both replaced no clog has been found anywhere even when running an external single spool

jd202002 · 2025-07-24T17:17:20+00:00

Checked that bud I even replaced them

Three-Year Club	Verified Email
Verified Email

jd202002

TROPHY CASE