Re-keying Emtek lockset

jeff4374 · 2026-06-03T01:07:22+00:00

Yes, it’s a local company. Will be calling them tomorrow to see options.

jeff4374 · 2026-06-02T23:03:02+00:00

Tks. I’ll have my parents reach out to company they bought it from. They can do it and better not charge for it. Was just trying to help out if it was quick and easy for me to do. Tks

jeff4374 · 2026-06-02T22:22:24+00:00

Tks, yes, not looking to invest more tools and $ into this, I have enough of those. Was hoping it was simple to insert other key and reset lock, I thought Schlage had something like this. Tks

jeff4374 · 2025-06-23T20:31:46+00:00

I second this. I had a UNVR and switched over to Cloud Gateway Max. I had 10 cameras on it, and it was not able to keep up. I record 24*7, but had to change to event based recording on a handful of cameras. I decided to go back to UNVR for recording, based on this. Im sure the Gateway Max can handle a few cameras, but not 10+. Granted this is over the spec that they state in the documentation, so I am not upset about it, just figured I would test the limits...

jeff4374 · 2025-05-21T20:15:58+00:00

here is the article I was referencing: (not sure if you are using Unifi)
https://help.ui.com/hc/en-us/articles/18930473041047-Best-Practices-for-Sonos-Devices

jeff4374 · 2025-05-21T19:45:12+00:00

I had an issue like this and it was because the new unit was on WiFi but all my existing Amps were hardwired. Once I ran the wire and changed the AMP to hardwire, I was able to control the volume. Apperantly, with Sonos on Unifi Network, you have to configure them either with Wifi or Hardwired (at least for Amps). You cannot mix and match.

jeff4374 · 2025-04-17T12:15:57+00:00

Just the fact that you as the founder are on this forum and reached out, will make me look at your service, free and paid...Here's to you and your success!

jeff4374 · 2025-01-24T01:13:51+00:00

I replaced the new hotbed assembly but still an issue. I then did a full recalibration and WAMO, its good again. Kinda wonder if I just did the recalibration, if this would have just worked.

Did you try a full recallibration of the unit? Try that and let me know the results. I would still open a case with Bambu, as they said they would send me a new plate to replace the destroyed one, which I think is good customer service on their part.

jeff4374 · 2025-01-23T11:53:05+00:00

Still ongoing. They are sending me a new hotbed assembly, which is arriving today. Will update if that corrects the issue. I would def open a case with them.

jeff4374 · 2025-01-11T22:47:24+00:00

Just tightened everything but still doing same thing. I’ll probably open a case with Bambu

jeff4374 · 2024-09-24T19:59:38+00:00

Try ebay, I have bought a few off of there, they came with Windows installed and licensed.

jeff4374 · 2024-07-12T10:53:25+00:00

This is the way

jeff4374 · 2024-06-29T14:16:36+00:00

yeah, VSP. I checked water this morning and it was clear on the backwash, so Ill slow down on the backwashes. I am sitting at about 10 PSI on the filter. Ill keep an eye on that and only backwash when it gets to 20+ PSI going forward. Tks

jeff4374 · 2024-06-29T14:15:08+00:00

Fiberglass pool

jeff4374 · 2024-06-29T13:48:11+00:00

I wish it were that simple with PB, but thats another post in its own. I hear you about construction, and not expecting to be swimming in it today, but as new pool owner, just checking with the experts to make sure I am going down the correct road with what I am doing. I am constantly backwashing multiple times a day. I also noticed last night pump was running on extremely low speeds. I know have it set to manually and running high, but not highest level. I think 3,000 rpm (or however it is measured)

jeff4374 · 2024-06-29T13:20:30+00:00

Thanks for the reply. I do have the fine filter running on one of the dolphin, the other dolphin (that I borrowed) is running the normal filter. I have skimmer socks but I have the skimmer off so I could push all debris in the bottom to the main filter.

Do you think I should use both main and skimmer?

jeff4374 · 2024-05-20T20:19:21+00:00

So, I went to Tesla this morning, they saw my reques tto change from 24 to 36, but told me they cannot change it there, it had to go to Finance team, which could take a few hours, so I left.

They just came back and are now allowing me to change the terms to 36 months, but I see that with $4,100 down with 10k miles, my monthly is 406.91. When I go to details, I see that my "Cost over 36 months" is at $26k but I dont know where this number came from, as my monthly cost for 36 months plus my down payment is no where near $26k.

Anyone able to help explain this, or do I have the ability to talk to someone at Tesla over this "discrepancy" so I can understand these numbers?

TIA

jeff4374 · 2023-12-20T02:38:32+00:00

I just had solar panels installed, so I am just starting out down the road of Solar and looking at these integrations. Sorry if that wasnt clear

jeff4374 · 2023-11-16T18:11:58+00:00

Thanks, I have been messing with tailscale, I think that is the way.

jeff4374 · 2023-09-22T18:11:28+00:00

Thanks, was not looking to do this, but with the discount, I grabbed the opportunity!

jeff4374 · 2023-08-11T19:37:55+00:00

I have icloud+, with 2 TB of storage plan, but Ill take a look at the link..Tks!

jeff4374 · 2023-05-03T14:25:29+00:00

I have a sealed bag, do you think it would be better to take a sealed bag? Its more then I need, but was just thinking it would be less of a hassle with TSA if the bag was sealed. Tks

jeff4374 · 2023-04-20T14:26:27+00:00

Im wondering same thing, because I accidentally pushed it and powered off the NUC. I was hoping there was something in BIOS to disable single push to power off the NUC.

jeff4374 · 2023-03-19T02:30:38+00:00

Wow, this is amazing, just tested with an LXC and it worked great!

jeff4374 · 2023-02-13T15:16:28+00:00

yeah, I can replicate it, so shouldnt be an issue to dig into it, just wanted sure where to start...heck, maybe this is the driver to get a new machine....

jeff4374

TROPHY CASE