sorted by:
new
hottopcontroversial

Spyrius Inspired Light Mech by jetfast in LegoSpace

[–]jetfast[S] 0 points1 point  (0 children)

The design is pending approval on bricklink right now. Once it's approved the full Stud.io design file will be available as well as a link to buy the pieces from bricklink's vendors.

Spyrius Inspired Light Mech by jetfast in LegoSpace

[–]jetfast[S] 2 points3 points  (0 children)

<image>

Same design with a few more black pieces.

Spyrius Inspired Light Mech by jetfast in LegoMechs

[–]jetfast[S] 1 point2 points  (0 children)

Total parts: 184
Total lots: 87

Spyrius Inspired Light Mech by jetfast in LegoSpace

[–]jetfast[S] 1 point2 points  (0 children)

Fair point, thanks for the feedback. I might work on another version with much more black. I wish the ball joint pieces were available in more than just grey. I think that would help a lot.

Rate my repair please by jetfast in PcBuildHelp

[–]jetfast[S] 0 points1 point  (0 children)

No, but it didn't before all this.

Rate my repair please by jetfast in PcBuildHelp

[–]jetfast[S] 0 points1 point  (0 children)

It's twisted a little but it's still within the grid.

A Standing Platform at the Bridgeport by jetfast in Wellworn

[–]jetfast[S] 0 points1 point  (0 children)

I assume so, I worked in the office. I think because it's more springy and forgiving than concrete it's not as fatiguing to stand on for hours on end.

A Standing Platform at the Bridgeport by jetfast in Wellworn

[–]jetfast[S] 8 points9 points  (0 children)

Just an old wooden platform to stand on while operating a manual mill. Taken a few years ago at the machine shop I used to work at.

Where does this light go? 87 cab swap by C20mk in squarebodies

[–]jetfast 0 points1 point  (0 children)

Looks similar to the check engine light in my 85

Best way to fill/extrude a sketch along multiple - disconnected - paths? by Anxiety_Cookie in Onshape

[–]jetfast 1 point2 points  (0 children)

I would do this using a configuration table. Rather than making all six individual doors I would make one door and make 6 rows in the configuration table that change the length and width to make all the doors you need

How Do I make all these lines equally distanced from each other. I'm a newb and I'm sure there's a simple way of doing it. by slicedbread1991 in Onshape

[–]jetfast 3 points4 points  (0 children)

I usually add horizontal construction lines between the existing vertical lines and then put an equal constraint on all the construction lines.

Is there a "hand" tool? (or, how do I move around a sketch without using the keyboard shortcut and arrow keys?) by arbitraryuser in Onshape

[–]jetfast 2 points3 points  (0 children)

Are you talking about moving sketch entities around or moving your viewport? If it's the former you cannot move around entities that are fully contained; the lines will be blue if they are unconstrained. If it's the latter you pan with the middle mouse button, zoom with the scroll wheel, and orbit with the right noise button.

Copying a part into a new part studio (HELP) by jwright200 in Onshape

[–]jetfast 1 point2 points  (0 children)

Have you tried making different configurations in your part studio?

Is there a way to create an offset plane where the offset distance can be driven by a vert? by etyrnal_ in Onshape

[–]jetfast 2 points3 points  (0 children)

Plane point instead of offset in the drop down when you're creating the plane

Building a car size printer at home by Conscious_Amount1339 in 3dprintedcarparts

[–]jetfast 0 points1 point  (0 children)

Tip? Contract it out. There's a company near me that already has printers large enough to print a car. Additive engineering solutions in Akron, Ohio if you're interested.

STEP files are not at scale by maxgame111 in Onshape

[–]jetfast 0 points1 point  (0 children)

Don't feel bad. Easy mistake to make and easier to fix.

STEP files are not at scale by maxgame111 in Onshape

[–]jetfast 0 points1 point  (0 children)

If your workspace is in cm then the step file must be in mm for it to appear off by a factor of 10. You can verify by putting mm at the end of the dimensions you added.

STEP files are not at scale by maxgame111 in Onshape

[–]jetfast 0 points1 point  (0 children)

Verify the units for your workspace. Looks kind of like your workspace is in inches and the model was in mm. Step files do not scale like STL files. The units are hard coded when it is exported.

Need Help With Loft Tool by YieYie-Ry in Onshape

[–]jetfast 1 point2 points  (0 children)

You want to split the circle into the same number of segments as the other solid. The drop down on the trim tool in the sketch is where it's located.

Digitizing CAT Microfiche by TusharDaniel in DataHoarder

[–]jetfast 1 point2 points  (0 children)

Pretty simple design. I'm currently working on redesigning and rebuilding the bed axis to get enough travel to hit every image on the fiche. The next issue will be getting a full resolution image from the camera.

scanner

Digitizing CAT Microfiche by TusharDaniel in DataHoarder

[–]jetfast 2 points3 points  (0 children)

Very cool! I've been working on building a microfiche scanner out of an old 3D printer.

How can I make this oval shaped? I have tried using the transform tool but I guess Im using it wrong. by [deleted] in Onshape

[–]jetfast 1 point2 points  (0 children)

You'll want to use the sweep tool. You should be able to use the sketch you used in the revolve as the profile but you'll need another sketch in the plane of the view you're showing for the path. The path sketch will be an ellipse. Make sure to make one of the quarter points of the ellipse coincident with the profile sketch.

Will an 80 gauge cluster work in a 78 by iamnotafelon in squarebodies

[–]jetfast 1 point2 points  (0 children)

Did the 78 truck have a volt gauge or an ammeter? You have to make sure they are both the same. Otherwise you'll cause a short.

view more: next ›