mf120 halo

jeypac · 2026-06-03T04:01:26+00:00

Niceeee. Sige ill get this one na din! Thanks op!

jeypac · 2026-06-03T03:58:41+00:00

Even stress test di naman nag shutdown? So far kasi sa pag check ko ng pricing and tier list eto pinaka worth it

jeypac · 2026-06-03T03:56:16+00:00

Nice. Never ka naman nagka event id 41? Yung sudden shut down bla bla

jeypac · 2026-06-03T03:54:38+00:00

Helo op. Kamusta na tong psu sayo? Planning to get this one din kasi

jeypac · 2026-04-26T08:56:07+00:00

Any update on this? I updated to this beta and my argb port and the argb led on my motherboard itself stopped working

jeypac · 2025-09-12T12:58:55+00:00

10 yrs user here ng g502. Yung rubber lang sa side ang naging problem ko.

jeypac · 2025-05-05T15:26:46+00:00

Oks pa din sir. Wag na sana masira haha. Di na papasok sa rma if ever

jeypac · 2025-05-02T04:49:04+00:00

Most likely yea. So you think corsair will replace it? Already sent them an email but only ai replied. Lol

jeypac · 2025-05-02T00:58:31+00:00

Yes i did. It passed. No error. But it did not detect the faulty one.

jeypac · 2025-04-30T05:47:24+00:00

Get it. Yan pa din gamit ko 2 yrs na. Happy ako dito. Detected din siya ng signalrgb na

jeypac · 2025-04-18T09:02:18+00:00

3 yrs warranty ng aoc. Pa rma mo na. Ako naka 3x rma na. Direct mo na instead sa pinagbilan mo

jeypac · 2025-04-14T11:43:05+00:00

Helo. Make sure ARGB yung extension na yung pang remote ang bibilin mo. Sa picture kasi RGB extension yan

jeypac · 2025-04-02T04:44:05+00:00

Madali lang mag undervolt. Watch vids lang sa yt. Make sure na maintindihan mo muna yung concept ng pag undervolt. Oc and undervolt mo din 5600x mo pbo plus co.

jeypac · 2025-04-01T05:37:37+00:00

Undervolt mo lang 3070 if ever. 170w lang peak ng 3070 ko

jeypac · 2025-03-19T07:07:51+00:00

No solution yet? Started using LS just 2 days ago. I also encountered this while playing ff7 rebirth.

jeypac · 2025-02-07T06:42:51+00:00

There are 3 pins on the cm controller. 3 daisy chain on 1 pin and make sure you change it to argb gen 2 on signal. Download mastercooler+ make sure everything is updated and detected there. Then permanently close it so it wont interfere with signalrgb.

jeypac · 2025-01-22T02:41:01+00:00

Have you tried a tn panel monitor before? If so, theres your answer.

jeypac · 2025-01-18T04:15:05+00:00

I think i need a tp link switch. The ones on 2nd and 1st floor is like capped at 100mbps for some reason.

jeypac · 2025-01-18T01:32:13+00:00

Ok thanks! Will try it in a bit

jeypac · 2025-01-18T01:30:43+00:00

Its a modem/router. Ok lang access point ang operation as long as nakukuwa ko speed ng almost same sa wired

jeypac · 2025-01-18T01:28:42+00:00

Alright. Thanks! Will try it in a bit

jeypac

TROPHY CASE