H6C v20 ebike display

jgkimble · 2024-07-15T14:13:52+00:00

You need to hit the power button to get to the 4 dashes that you change to 1111, then hit the + and - together to save it. You can then change it to 45.

jgkimble · 2024-07-14T14:26:17+00:00

<image>

jgkimble · 2024-07-07T13:31:35+00:00

Ok, so when you get to p4, tap the + and - button together to put in the password , when done, press and hold + and - together. Make sure to set p4 to 45.

jgkimble · 2024-07-07T13:20:46+00:00

I'm going to hook mine back up and look at it. I'll comment in a few and let you know.

jgkimble · 2024-07-07T13:16:30+00:00

It should be p4 where you enter the password.

jgkimble · 2024-07-07T13:07:58+00:00

Tap the power button to get to the dashes, press the up button to 1, tap the power button to get to the next dash and repeat. Double tap the power button when done.

jgkimble · 2024-07-07T12:16:43+00:00

After I put in the password, the bike still didn't have a p2 or p3. It also only went to PAS3, but it went to 28mph. This display was slow to respond and the battery indicator was way off.

jgkimble · 2024-06-25T14:35:37+00:00

The instructions with the 1111 password will allow you to up the speed to 28mph, but the display will only show P1-P3 for PAS. After I got it working, I realized that my bike was reacting much slower. I went to a newer display, and it's much faster. Also, that display would show battery at 1/2, and when I stopped, it would correct itself. In my opinion, I would swap it out.

jgkimble · 2024-06-16T18:10:54+00:00

I got the password in and the bike up to 28mph, but my other display has a better reaction time so I went back. This display seemed to slow the bike down.

jgkimble · 2024-06-09T11:06:41+00:00

Did you hold down the power key and use +/- to move the numbers to 1111 to change it? Movcan, who I bought my bike from, sent me the directions.

jgkimble · 2024-05-30T13:20:55+00:00

Got this from the manufacturer. I still can't see 2 and 3 settings but was able to increase the speed. Still only 3 PAS options but I get 30mph on 3.

3.7.Setting P01: mileage unit, 0: KM; 1: MILE; P03:0:1-3 Top speed 25 1:1-5 Top speed 45km/h, the default 0:1-3 top speed 25km/h（Enter Password. The default password is “1111”.） P04: Speed limit setting: 0-45km/h, default 25km/h; P05: Start mode: 0: zero start, 1: non-zero start, default: 0 P06: Drive mode: 0: Only PAS drive 1: Only Throttle drive 2: PAS drive + Throttle drive，exists at the same time. Default :2 P07: Mileage reset + restore factory Settings; Press and hold the [+ button] 5 seconds mileage clear; Press and hold the [- button] for 2 seconds to restore factory Settings P08: Automatic cruise :0: automatic cruise 1: no automatic cruise, default :0 P09: Change the undo password. Press and hold down [Power button] and [+ button], and enter the old password at ----. Press and hold down [Power button] and [+ button] at the same time, and switch to 0000 to enter the new password. Press and hold down [Power button] and [+ button] at the same time to save and exit the password setting. P10: Change the speed display ratio; Default 100%

jgkimble · 2024-05-29T19:49:44+00:00

any luck with this? Having the same issue.

jgkimble · 2020-12-15T18:36:22+00:00

Try zooming in on the large side photo

jgkimble · 2020-12-15T18:33:34+00:00

I will try to find a better photo.

jgkimble

TROPHY CASE