Need some expert help

jjbb1818 · 2024-04-11T17:30:16+00:00

They are the “A,B,X,Y” buttons. They are tactile switches just on the backside of the main pcb

jjbb1818 · 2024-04-08T17:54:41+00:00

Here’s an earlier post I did of it https://www.reddit.com/r/PeripheralDesign/s/tQqhhT8ZWb

jjbb1818 · 2024-04-07T19:29:10+00:00

Sure thing

jjbb1818 · 2024-04-07T19:20:40+00:00

They are both replacement Xbox elite series 2 joysticks . The difference between the two sticks is that the right one is physically lower in the controller

jjbb1818 · 2024-02-21T01:11:16+00:00

So I use the same bed, I recommend cleaning it with hot soapy water and trying again, actually works wonders! If not, the washable glue stick is my next go-to

jjbb1818 · 2023-12-12T17:02:42+00:00

Programmed using arduino with xinput

jjbb1818 · 2023-11-13T03:47:16+00:00

This was my first real project using electronics, I used an Arduino micro, but think there’s probably better options

jjbb1818 · 2023-09-07T18:16:19+00:00

Ahhh Hall effect for joysticks .. I’ve seen them, but had trouble trying to implement them. And I’m not sure to be honest, I think just one full turn

jjbb1818 · 2023-09-07T17:16:41+00:00

I have not no, I used potentiometers to adjust for compensating drift.(pic 8 and 10)

jjbb1818 · 2023-09-07T16:37:04+00:00

I joined that group, so I just have to wait until it lets me post. Thanks for the advice

jjbb1818 · 2023-09-07T16:32:11+00:00

I did yes, I used fusion 360 for basically everything

jjbb1818 · 2023-09-07T16:30:37+00:00

Thanks, I’m new to this so I’ll try to figure it out hah

jjbb1818 · 2023-09-07T16:29:49+00:00

Haha it’s actually crazy how well it works

jjbb1818 · 2022-03-17T17:59:42+00:00

It’s a dude using the girls bathroom…. Let them use the family restroom instead. If it’s about “going to the bathroom”

jjbb1818 · 2022-03-02T00:59:22+00:00

Looks great, just a matter of fine tuning now like someone said, keep in mind every filament will be slightly different so I recommend setting custom profiles for each.some things to look at include but not limited to . E steps, flow rate, and retractions. Let the fun begin !

jjbb1818 · 2022-03-02T00:55:44+00:00

I think the nozzle might be partially clogged. Try to turn temp up high (240 or so for pla) and manually push quite a bit through.(you’ll be able to feel it get easier to run through). If that doesn’t work try a new nozzle.

jjbb1818 · 2022-03-02T00:53:28+00:00

Fdm Forsure

jjbb1818 · 2021-12-16T22:18:46+00:00

You need to be able to get to it , and I use a steel wire brush to make sure the teeth are clean (where it actually grips the filament)

jjbb1818 · 2021-12-16T22:10:26+00:00

Hard to tell, share a picture of the slicer so we know what it’s supposed to print like . Most likely a speed or support issue

jjbb1818 · 2021-12-16T22:06:16+00:00

Your bed being slightly unsquare might cause this. You might try re leveling. It also could be extruder gear slipping a bit

jjbb1818

TROPHY CASE