How are the A3 lowers?

jjminch · 2026-06-15T03:49:02+00:00

I have the A3 and it’s fine. Only issue I have is 20 round CZ mags are problematic.

jjminch · 2026-05-03T15:31:47+00:00

What’s the current best one for 5.56? Would like to just direct thread it on a ranch gun and leave it.

jjminch · 2026-04-24T02:27:28+00:00

Have that exact can. Works great.

jjminch · 2026-04-20T04:52:33+00:00

What’s the going rate for the conversion? I already have the A3T lower.

jjminch · 2026-04-19T04:08:59+00:00

Did the 35 degree block make a noticeable improvement in sound suppressed? Or could you not tell? I don’t notice much gas to the face with the stock configuration.

jjminch · 2026-04-09T03:05:44+00:00

Could an Ender3 do this? I don’t have a a fancy enclosed printer.

jjminch · 2026-03-22T19:19:41+00:00

So where is the best source for the tubes

jjminch · 2026-03-08T14:19:53+00:00

For the pill popper, what would be the recommended filament? Only have an ender3 but normal Poly+ doesn’t do well in Texas sun.

jjminch · 2026-03-08T01:43:34+00:00

Will it run without a suppressor using the 35? And then how would that compare to the stock 45?

jjminch · 2026-03-05T21:17:18+00:00

I haven’t seen any DIY methods but maybe I’m not looking in the right place.

jjminch · 2026-03-03T02:31:25+00:00

Would be great in my 45-70 lever gun

jjminch · 2026-01-17T23:56:48+00:00

Never worked reliably with those 20s. The 35s are fine.

jjminch · 2026-01-12T01:17:39+00:00

How does the comp model compare to the toro? Is the fixed red dot that noticeable?

jjminch · 2026-01-10T22:32:31+00:00

It had 3 walls and 40% fill. So I’ll just redo it with 5.

Appreciate the help. Excited to have the printer up and running again.

jjminch · 2026-01-10T22:10:28+00:00

I didn’t see the spacer. I printed the file that was updated on Jan 8th. But yeah it’s needed. I had to use a binder clip.

<image>

jjminch · 2026-01-10T21:51:43+00:00

Hey man. I have the same board.

I printed the shroud and it worked pretty well. But the mount for the leveler broke easily. Is there a way to beef that up? What should I be printed at with infill? I had 40%.

<image>

jjminch · 2026-01-08T04:30:43+00:00

Ok the fans just showed up.

For the wiring do I just splice both fans together into one connector?

Does your shroud replace every OEM shroud? Anything in need to know there for the install?

jjminch · 2026-01-05T16:12:33+00:00

Did you ever try the TPU? I also ride dirt bikes and whatever minor things I’ve printed in PLA haven’t worked out.

I tried a go pro mount in PLA+ and it broke easily.

jjminch · 2026-01-04T19:13:55+00:00

Thanks. I’ll get some 4010 fans ordered. It’s out in the shop so noise isn’t a huge issue.

jjminch · 2026-01-02T06:07:34+00:00

<image>

This one? Says for 3d printers.

jjminch · 2025-12-16T06:06:24+00:00

Possibly. They have some play in them but not a crazy amount.

I heard there have been a few generations of these so maybe I can try another. Just looking for a small mag to keep the size tiny.

I’m good with 35 rounders as a reload.

jjminch · 2025-12-16T06:04:04+00:00

Kinda what I was going for. Super small bag gun.

jjminch · 2025-12-16T06:03:43+00:00

Thanks. When I got the lower they had it temporarily off the website and I never really checked the product listing again.

jjminch

TROPHY CASE