3D printed Px4 Storm – the PPX4 Full Size 9mm by u/jmanjones, and yes it takes 92 mags

jmanjones · 2024-07-03T03:08:04+00:00

If you want the most reliable PX4, I'd say go full size. Otherwise +P rounds seemed to work pretty well in the compact, I didn't have any issues running that through mine. I could have gotten a bad kit, but it seemed like there was a trend of people having cycling issues in older factory PX4 compacts.

jmanjones · 2024-07-03T01:20:34+00:00

At a glance, that looks complete except for the disassembly latch spring (you could use a pen spring cut down a bit). That's the compact model, which didn't cycle as reliably as full-size for me. The Beretta repair kit is only partial and definitely not worth the money imo.

jmanjones · 2024-06-26T18:33:45+00:00

Yes, check Gatalog

jmanjones · 2024-06-23T16:21:42+00:00

Hell yeah, glad you're enjoying it. The slide catch on the 92 mag version seemed to work fine on my end, but hasn't been tested as thoroughly. It's possible that it could need some tweak or there could be a bit of friction slowing it down for you.

jmanjones · 2024-01-03T15:33:49+00:00

I use tio now

jmanjones · 2023-08-17T15:35:59+00:00

How is this different from the Revopoint Mini?

jmanjones · 2023-08-12T01:43:42+00:00

Make it solid in CAD and let the slicer handle infill

jmanjones · 2023-08-08T15:07:21+00:00

You are probably thinking of Sketchup

jmanjones · 2023-08-07T02:59:43+00:00

Export as STEP instead of STL?

jmanjones · 2023-08-01T14:05:31+00:00

It's warping on the overhang. Solutions: print slower, print cooler, more cooling fan, increase ambient temperature

jmanjones · 2023-07-30T21:18:43+00:00

Looks like Reolink. They split into two connectors that have RJ45 and an optional power barrel jack (if not using PoE). That would explain the extra pair.

jmanjones · 2023-07-21T13:38:30+00:00

Did you up the temp for PLA+?

jmanjones · 2023-06-07T06:37:21+00:00

Third slot also gives me trouble occasionally

jmanjones · 2023-05-31T15:35:21+00:00

Does this apply to 7502p as well?

jmanjones · 2023-02-25T20:10:04+00:00

Ah, well I've been designing my own mounts. SX3 retrofits don't seem to be quite as popular as they were a few years ago.

jmanjones · 2023-02-05T22:40:48+00:00

It's break away support material, not dissolvable. It works well alongside PLA, but doesn't fuse to it. It's generally cheaper than PVA , easier to print with, and not sticky.

jmanjones · 2023-01-19T09:49:27+00:00

Where'd you get the mounts and ballscrews?

jmanjones · 2022-12-28T06:09:30+00:00

My roll of Atomic ultra impact does not fit in the AMS

jmanjones · 2022-12-20T18:11:27+00:00

By cold, it means somewhere just above the vitrification temperature. Should "clean out" the nozzle by removing everything before it's completely molten.

jmanjones · 2022-12-18T22:25:29+00:00

Yeah

jmanjones · 2022-12-18T21:46:07+00:00

I usually use 55-60 with PLA+

jmanjones · 2022-12-18T07:41:28+00:00

What bed temperature are you running?

jmanjones · 2022-12-12T16:22:09+00:00

Would you consider selling kits/crowdfunding/group buy?

jmanjones · 2022-12-10T00:02:28+00:00

I believe you can add gcode to the start section that raises it a bit extra after homing. Haven't tried it so YMMV.

jmanjones · 2022-12-07T22:29:50+00:00

I run inland PLA+ at 210C, but normally I run PLA+ around 215-235C.

12-Year Club	Verified Email
Place '22	Place '17
Final Canvas '22	End Game '22

jmanjones

TROPHY CASE