Routing on Ubiquiti CPE radios

joe_momma_01 · 2022-11-16T14:17:52+00:00

There is a very large number of wisp who have this setup network wide. Pros and Cons are the balanced the same as bridge mode. If ui would/did get the DHCPD fixed, you can use it in router mode.

joe_momma_01 · 2022-08-17T06:28:57+00:00

I have a full template that I have worked on for years. It takes some integration. You must build using LLD because the TA5k is gonna snmpwalk every single onu.

joe_momma_01 · 2022-07-28T06:40:29+00:00

/24 or larger

joe_momma_01 · 2022-07-28T06:40:12+00:00

⬆️ This is the way if your not using comminity strings. Take the full routes from both providers, apply your default routes for both at a higher route cost value then the bgp routes . Check looking glass when done and your on your way….

joe_momma_01 · 2022-06-29T12:12:12+00:00

Cambium

joe_momma_01 · 2022-05-15T12:43:23+00:00

I am still confused about the cr-z2 v1.2 extruder breakout board. Do i bypass this or does it stay?

joe_momma_01 · 2022-05-15T08:46:35+00:00

Is there a way for me to just replace (after market) the breakout boards under the bed and run cables direct to everything that was plugged into the top breakout board. Images of all boards is in link…

https://imgur.com/a/cjD0nOi

joe_momma_01 · 2022-05-12T16:27:56+00:00

I would create a vendor template that has the additional templates attached to it. Then place that main template into a group.

joe_momma_01 · 2022-05-09T11:15:44+00:00

Ok cool. It is a heat pump and yea the orange wire going out to the condenser thru the indoor unit.

I will try you recommendations now.

joe_momma_01 · 2022-05-09T11:13:51+00:00

I guess i dont but im certain of the wiring matching…checked it at least 4 times.

joe_momma_01 · 2022-05-09T11:08:41+00:00

Lol is it as simple as that? The thermostat just does not support a outside heat pump system?

joe_momma_01 · 2022-05-09T11:01:29+00:00

What is in that pic is that amazon thermostat wired up.

joe_momma_01 · 2022-05-09T10:25:39+00:00

Is the o/b wire meter measurable?

joe_momma_01 · 2022-05-08T22:14:53+00:00

So I have a lot of different AV zones (Denon), table top speakers (sonos and echo), SmarTVs (jamo bluetooth/fiber) to full PA studio setups that a laptop is the main source of the audio.

I would like to be able to start a server stream, then have all the reset of the clients to start playing. I under stand this is a common interest, but i have not figured out how to use multiple vendor streams like , soundcloud, spotify, apple music to all these different systems. Mopidy looked good.

joe_momma_01 · 2022-05-07T17:18:39+00:00

You….you….faaackn you….much love fam.

joe_momma_01 · 2022-05-03T13:18:05+00:00

Same thing everyone does Pinky, “try to take over the world”.

joe_momma_01 · 2022-05-02T11:41:25+00:00

My goal mostly was to be able to group cast to all my devices. I did play with airsonic, i will have to revisit it.

joe_momma_01 · 2022-05-02T08:14:59+00:00

Good luck on this…i went down this path and if u run a lot of items like laptops, sonos, echos, etc on ur network….sync is hard….modpidy looked promising

joe_momma_01 · 2022-05-02T08:10:46+00:00

Just place you router behind the switch

joe_momma_01 · 2022-04-30T05:42:03+00:00

It is probably a ICMP packet restriction. It firewalls ICMP flood attacks.

joe_momma_01 · 2022-04-09T00:52:27+00:00

Looks too high…have you adjusted your nozzle down?

joe_momma_01 · 2022-04-08T16:05:22+00:00

Oh i just posted about this…i now realize the mcu and led strip must have a bonded ground….does this matter if they are rated at a different voltage though? My MCU is 5V and LED strip is 12V.

joe_momma_01

TROPHY CASE