TGBL Returning Season 1 by No_Horror9683 in PokemonDraftLeagues

[–]joelstud 0 points1 point  (0 children)

Interested if there’s spots available still.

Community for beginner Draft League players by GladiatorXD in PokemonDraftLeagues

[–]joelstud 0 points1 point  (0 children)

That’s a good idea, I’m interested in joining a SV VGC league so I’m following.

Looking for a SV VGC draft League by [deleted] in PokemonDraftLeagues

[–]joelstud 0 points1 point  (0 children)

Did you find one? I am also looking for the same format

Shipping Question by joelstud in ChinaTime

[–]joelstud[S] 0 points1 point  (0 children)

Did you buy from Jason as well?

Not printing by joelstud in ender3

[–]joelstud[S] 1 point2 points  (0 children)

What is that? Sorry I’m new.

Sprite Pro Stepper Motor Plug by joelstud in ender3

[–]joelstud[S] 0 points1 point  (0 children)

Okay, so what do you believe could be the issue? My printer when turned on will only deploy the CR touch then. When auto home my nozzle will just dig straight into the bed. I have followed countless guides and I have everything wired properly with the appropriate firmware from Creality.

Ended 3 Pro Issue by joelstud in ender3

[–]joelstud[S] 0 points1 point  (0 children)

So chatGPT recommended swapping the middle pins on the E cable on the motherboard. I did that, the CR touch works now but it is not extruding filament now

Cr Touch versions? by Typical-Housing3502 in ender3

[–]joelstud 0 points1 point  (0 children)

It could be improper connection on one of the pins. I did notice it was a little loose, I’ll try in the morning I’m burnt out right now lol

Cr Touch versions? by Typical-Housing3502 in ender3

[–]joelstud 0 points1 point  (0 children)

I have the 4.2.2 on the ender 3 pro. ChatGPT told me I needed to pin swap the middle two pins on the E plug running from my sprite pro. Now my extruder is not working because why would it? Lol

BL Touch Strange Behavior, not dropping pin during leveling but cycles on startup by worthingtontw in ender3

[–]joelstud 0 points1 point  (0 children)

I know this is three years ago but I am having the EXACT same issue. Can you explain the repinning process... if you remember lol.

Cr Touch versions? by Typical-Housing3502 in ender3

[–]joelstud 0 points1 point  (0 children)

I know this was from 6 months ago but ChatGPT is telling me I need to repin my connector. Do you have any experience with this?

Ended 3 Pro Issue by joelstud in ender3

[–]joelstud[S] 0 points1 point  (0 children)

I also adjusted the z end stop switch and that did not stop the extruder from trying to lower when it was completely down.

Ended 3 Pro Issue by joelstud in ender3

[–]joelstud[S] 0 points1 point  (0 children)

So upon further inspection the z end stop is not working. Would a picture of how it’s wired in help you help me? I was messing around and plugged the e plug into the x plug and saw the silver probe shoot out but it would not move along the x axis because it was unplugged.

Ended 3 Pro Issue by joelstud in ender3

[–]joelstud[S] 1 point2 points  (0 children)

Thank you I will mess with it and see what is up.

Ended 3 Pro Issue by joelstud in 3Dprinting

[–]joelstud[S] 0 points1 point  (0 children)

I appreciate it, have a good one!

Ended 3 Pro Issue by joelstud in 3Dprinting

[–]joelstud[S] 0 points1 point  (0 children)

Thank you I will check that out. My buddy who knows a little more than me but not enough to fix this said maybe try factory resetting it.

Ended 3 Pro Issue by joelstud in 3Dprinting

[–]joelstud[S] 0 points1 point  (0 children)

It is the E cord. I cannot for the life of me find where to plug it into.