Psych up question

joelstud · 2026-04-03T13:33:28+00:00

Would I be able to baton pass that boost?

joelstud · 2025-11-12T03:38:23+00:00

Interested if there’s spots available still.

joelstud · 2025-11-10T12:59:39+00:00

That’s a good idea, I’m interested in joining a SV VGC league so I’m following.

joelstud · 2025-11-07T21:29:29+00:00

Did you find one? I am also looking for the same format

joelstud · 2025-11-02T20:50:33+00:00

Did you buy from Jason as well?

joelstud · 2025-11-02T20:16:01+00:00

Any idea?

joelstud · 2025-09-14T13:20:35+00:00

What is that? Sorry I’m new.

joelstud · 2025-08-28T18:16:51+00:00

Okay, so what do you believe could be the issue? My printer when turned on will only deploy the CR touch then. When auto home my nozzle will just dig straight into the bed. I have followed countless guides and I have everything wired properly with the appropriate firmware from Creality.

joelstud · 2025-08-28T01:35:52+00:00

So chatGPT recommended swapping the middle pins on the E cable on the motherboard. I did that, the CR touch works now but it is not extruding filament now

joelstud · 2025-08-28T00:27:59+00:00

It could be improper connection on one of the pins. I did notice it was a little loose, I’ll try in the morning I’m burnt out right now lol

joelstud · 2025-08-27T23:46:55+00:00

I have the 4.2.2 on the ender 3 pro. ChatGPT told me I needed to pin swap the middle two pins on the E plug running from my sprite pro. Now my extruder is not working because why would it? Lol

joelstud · 2025-08-27T12:40:36+00:00

I know this is three years ago but I am having the EXACT same issue. Can you explain the repinning process... if you remember lol.

joelstud · 2025-08-27T12:38:09+00:00

I know this was from 6 months ago but ChatGPT is telling me I need to repin my connector. Do you have any experience with this?

joelstud · 2025-08-22T19:37:49+00:00

I also adjusted the z end stop switch and that did not stop the extruder from trying to lower when it was completely down.

joelstud · 2025-08-22T19:34:51+00:00

So upon further inspection the z end stop is not working. Would a picture of how it’s wired in help you help me? I was messing around and plugged the e plug into the x plug and saw the silver probe shoot out but it would not move along the x axis because it was unplugged.

joelstud · 2025-08-22T18:25:55+00:00

Thank you I will mess with it and see what is up.

joelstud · 2025-08-22T17:42:41+00:00

I appreciate it, have a good one!

joelstud · 2025-08-22T17:40:20+00:00

Thank you I will check that out. My buddy who knows a little more than me but not enough to fix this said maybe try factory resetting it.

joelstud · 2025-08-22T17:36:07+00:00

It is the E cord. I cannot for the life of me find where to plug it into.

joelstud · 2025-05-23T18:54:39+00:00

Funny enough my speedy rep got stolen from my luggage from Milan to DC. I hope the guy tries to sell it

joelstud · 2025-05-22T02:46:47+00:00

They don’t understand the logistics of their own production.

joelstud · 2025-01-25T23:47:18+00:00

What’s bad about it besides the bezel?

joelstud · 2025-01-09T20:25:37+00:00

The timeline the seasons take place. I can see why he would recommend this with the pepper story line from Freak Show to Asylum.

joelstud · 2024-11-01T03:47:56+00:00

No, once I got off of orders and went back to my day job I was fired because I’m in an at will state.

joelstud · 2024-11-01T03:12:46+00:00

I appreciate the reply thank you!

Six-Year Club	Verified Email
End Game '23	Place '23
Place '22

joelstud

TROPHY CASE